减速箱采用硬齿面磨齿斜齿面传动减速箱。
如果这时候你急着用水去冲，因为附着的小沙石很容易把漆面磨花。
If at that time you rush to water to blunt, because of the small sand attached easily lacquer face wear away.
群体或许会将不成文的规范强加于我们，扭曲或夸大我们的决定，甚至磨钝我们的创造性，但这些只是群体力量的一个方面，另一方面这种力量使得群体强壮。
Groups may impose unwritten norms on us, warp or exaggerate our decisions, even dull our creativity, but these effects are often the flip side of forces that make groups strong.
齿轮齿形采用磨齿加工，齿面采用智能控制渗碳淬火技术，齿轮的强度高、韧性和耐磨性好。
Employing abrasive machining for the form of the gear and intellective-control carburizing and quenching technology for the surface, the gear is with high intensity, strong tenacity and wearability.
闸板两面均经过精密精磨加工，避免损坏填料和阀座。
They feature a precision ground finish on both sides to prevent packing and seat damage.
通过这些方法所获得的数据能够从一方面或多方面反映油品的性能和磨粒的特性，从而得到机器故障信息。
The acquired data by the above methods can reflect oil performance and characteristic of particles, and be further analyzed to the faults in a monitoring machine.
给出螺旋面钻尖刃磨机床的基本结构及其工作原理。
Basic structure and operation principle of the parallel grinder for helical drill point grinding is presented.
FK系列踵趾面修整机主要用于梳棉机盖板铁骨的修磨。
FK Series flat End Milling Machine is used for modifying all kinds of flat iron.
本文还提出了由碳化物数量、分布、磨损面硬度等因素构成的抗磨参数与相对耐磨性的线性关系。
Authors suggest the linear relationship between the anti-abrasion parameters consisting of the amount and distribution of carbides, abrasive surface hardness and the abrasion resistance in this paper.
方法：根据不同类型桩钉及根面所处位置，分别采用钳取、根尖挺挺出及钻磨取钉等方法。
Method: The separate application of clamp, root elevator or drilling root canal according to different type of post pin and place of root surface.
渐开面包络环面内螺纹蜗杆砂轮磨齿，是一种硬齿面齿轮精加工的新型工艺。
Grinding gear with the toroidal involute interior thread worm grind wheel is a new kind of process in hard surface gear finish machining.
结果：寰枕关节面不同的比例关系，决定枕髁的磨除范围。
Results: Different ratio relations to atlantooccipital joint interfaces were decided for condylar extension drilled.
本文介绍了LX88A制取的工艺特点及涂层性能，并分析了类似于流化床作业面所经受的冲蚀磨损与磨粒磨损过程。
This article introduces the technology characteristics and coating functions of LX88A, as well as the abrasion and erosion wear resistance processes.
建立平行、不可展直纹面数学模型，确定超声磨削加工平行、不可展直纹面时磨轮空间轨迹及其算法。
The mathematical model of parallel and undevelopable ruled surface was constructed, the algorithm for NC ultrasonic grinding surface was founded.
研究以珩代磨的硬齿面齿轮加工方法和珩齿机理具有重要的现实意义。
The study on the method of machining hard teeth profile gear of honing instead of grinding and honing mechanism has the meaning of important reality.
根据疲劳强度的可靠性设计理论，对球磨机的磨头与筒体法兰结合面处的联接螺栓进分了抗疲劳分析，建立了一套可分的设计理论和机算方法。
Depending on the reliable design theroy of fatigue strength, the paper deals with the analysis method between drum and grinding head of a ball mill.
本文介绍了新安江电站溢流坝面环氧砂浆抗冲磨涂层的老化状况研究；
This paper introduce the research on aging effects of the Xinanjiang hydropower station.
采用CMM齿轮检测仪测量磨齿机误差补偿前后所加工齿轮齿面误差。
Tooth deviation of the grinding machine both before and after the error compensation are measured by using CMM gear measuring device.
渐开面包络环面内螺纹蜗杆砂轮磨齿，是一种硬齿面齿轮精加工的新型工艺。
A worm grinding wheel used to grind gear wheel is designed to increase the gear precision.
介绍在硬齿面直齿锥齿轮刮削加工中研中心孔磨内孔的技术要求；机床调整，切削速度，刮削量及次数的选择。
The introduction is the strong and straight cone the wheel gear pare away to process the inside, whetting center the bore, whetting the inside bore in the strong wheel gear.
而相邻原机件叶片弦宽尺寸超差，锯齿形工作接触面积小，以及非工作面局部碰磨，是引发故障的次要因素。
Other causes include the out - of - tolerance of blade chord width between adjacent blades, the undersize contact area of serrated working side and the local wearing of non - working side.
本机是制革行业用于皮革修饰粒面表面或修磨革里之工序，使加工后的皮革绒面美观，平整，均匀细致，手感丰富，同时去除革面缺陷。
The machine is designed to finish grain surface and leather lining, further, the defects on leather surface, for beautiful, fine and smooth suede surface with full fell.
基于非共轴螺旋面钻尖的刃磨原理，建立了刃磨参数的数学模型。
Mathematical model for hyperboloid grinding of twist drill and relationships between drill design and grinding parameters are introduced.
为了提高面齿轮副的强度并解决其磨齿问题，提出了弧线齿面齿轮副的一种新的加工方法，并研究其啮合特性。
To improve tooth strength and make tooth grinding implement for face gear, a new generating method of face gear drive has been proposed, and the meshing characteristics are investigated.
所有加工面，包括磨整过的表面，都必须进行磁粉探伤。
All (100%) machined areas, as well as grinded surfaces must be inspected by magnetic particle.
介质的存在会对磨屑的产生、演变、消失既有促进的一面又有抑制的一面，其竞争结果视具体工况而定。
The generation, evolvement and disappearance of wear debris are sometimes promoted and sometimes restrained by aqueous media, the competitive results depending on the experimental conditions.
另一方面，轮对相对构架的强烈振动，也可能成为车轮非正常磨耗即剥离以及某些波长轨道波磨的一个重要因素。
On the other side, such strong vibration may also become an important factor of abnormal wheel wearing, wheel spalling and rail corrugation of certain wavelengths.
另一方面，轮对相对构架的强烈振动，也可能成为车轮非正常磨耗即剥离以及某些波长轨道波磨的一个重要因素。
On the other side, such strong vibration may also become an important factor of abnormal wheel wearing, wheel spalling and rail corrugation of certain wavelengths.
应用推荐