热电偶时创建两个不同材料接触和联络点，产生一个小开路电压随温度的变化。
A thermocouple is created when two dissimilar materials touch and the contact point produces a small open-circuit voltage as a function of temperature.
由此可以较好地解释高温超导氧化物材料的超导转变温度随空穴浓度的变化行为。
We can explain that the transfer temperature of high temperature superconductive oxides change along with the concentration of holes.
由于沥青混凝土材料强度的温度依赖性，弯沉以至路面结构承载能力都随温度而变化。
Since asphaltic concrete materials are temperature dependent in nature, measured deflections and hence the structural capacity of pavement vary with temperature.
通过实验的方法测定耐火保温材料的导热系数，测算出耐火保温材料的导热系数随温度的变化规律。
We have done experiment to measure the thermal conductivity of insulation material KT-TC, and found out the relation between thermal conductivity and temperature.
模型考虑了工件材料的热物理性质随温度的变化以及处理参数的影响。
The model deals with the variety of material's thermal-physical properties, the parameters of plasma-arc treatment.
材料的热、力学性能参数随温度变化；
Temperature-dependent thermal and mechanical material properties are used.
热敏变色衣料颜色会随温度变化而不断变化，这是因为在衣料中添加了由高分子材料制成的变色剂。
This is because a discoloring agent composed of a high polymer structure has been added to the clothing material.
通过理论计算推导出材料表面发射率随温度的变化趋势，结果表明，材料表面的发射率是随着温度的升高而降低。
Theoretical calculations of the emissivity of material surface were shown that the emissivity of material surface decreases with the temperature increases.
本文采用极性的丁腈橡胶与短碳纤维复合，探讨了碳纤维及碳黑含量对复合材料电性能影响，以及该材料电性能随温度的变化情况。
The effect of carbon fiber content, carbon black content and temperature on the electic conductivity of the composite was studied in this paper.
再利用超越方程和我们制备的铁氧体材料的参数对其差相移随温度的变化进行数值计算，结果表明随温度的升高差相移减小。
Transcendental equation and parameters of ferrite materials prepared by ourself have been used to calculate the variation of differential phase with temperature.
弹塑性基体复合材料的特征相变温度偏移随纤维体积分数的变化规律与弹性基体复合材料的变化规律不同，其热相变特性有显著的区别。
The results show that the characteristics of thermal transformation behavior of SMA composites with elastic matrix are different markedly from those with elastoplastic matrix.
计算中考虑材料物理性能随温度的变化，并运用单元激活技术模拟多道焊焊接过程。
The change of material property depending on temperature was considered in computation. The element birth technique was adopted to simulate multi-pass weld.
单位压边强度随温度的变化规律与拉深成型过程中材料的软化与硬化作用有关。
The evolution of blank hold pressure is determined by the effect of work hardening and softening during deep drawing process.
模型中考虑了电、热、力的耦合以及材料物性参数随温度的变化，在电热耦合模型中计入接触电阻与闪光烧损对产热过程的影响；
In addition the material physical parameter variation with temperature was considered in the model. The contact resistance and flash melt were considered in the electric-heat coupling model;
根据食品品质损失动力学理论，分别建立不同温度、不同包装材料蛋糕的酸价、过氧化值随贮藏时间变化的动力学模型。
According to kinetic theory the loss of food quality, were established at different temperatures, different packaging cake acid value, peroxide value with storage time-varying dynamic model.
这样就得到两种不同材料的密封件沿轴向的温度分布，分析了温度随压力的变化规律，散热量及密封材料的耐热性能。
According to the temperature values measured, changes of temperature field in the center of sealing element have been calculated by the heat - tran...
有限元模型中选用三维实体单元，考虑材料物理性能随温度的变化和周边对流、辐射散热的影响。
The 3-d solid elements were used in FEM model, and the effect of temperature, and the heat convection and radiation of boundary on material properties were considered.
有限元模型中选用三维实体单元，考虑材料物理性能随温度的变化和周边对流、辐射散热的影响。
The 3-d solid elements were used in FEM model, and the effect of temperature, and the heat convection and radiation of boundary on material properties were considered.
应用推荐