这项技术的使用使得阀体变得简单小巧。
The use of these technologies allows the valve to be simpler, smaller and smarter than traditional venting systems.
安装时要使阀体箭头指向水流方向。
Install with the arrow on valve body pointing in the direction of flow.
然后将阀座和O形环从阀体中拉出。
彻底清洗安全阀阀体的所有内部表面。
Thoroughly clean all inside surfaces of the relief valve body.
电磁先导阀操作提供交流与黄铜阀体。
Solenoid pilot operated valves available AC operated with brass bodies.
从阀体镗孔内拆卸固定器。
除了阀体以外，所有部件都是可更换部件。
All components except valve bodies are available as replacement parts.
这道修整工序省去了配置橡胶隔膜的阀体。
This finishing operation is omitted on bodies receiving rubber diaphragms.
将手柄从阀体上拉出。
阀体和阀座的连锁结构防止被冲洗出或吹出。
轻巧的镁合金阀体。
将防溅保护的一半滑动到安全阀阀体的沟槽上。
Slide one half of the splash guard into the groove on the relief valve body.
这些阀门包含两个线圈、一个阀体和阀芯总成。
These valves contain two coils and one valve body and spool assembly.
逆时针方向旋转拆卸旋钮，同时将其拉出阀体。
Remove knob by counter-clockwise rotation, simultaneously, pull away from body.
造船工业。带自动阀的测深管测头。阀体详图。
Shipbuilding . head of sounding pipes with self - acting valve . details of body.
从阀杆上拆卸手柄，向上提升并将手柄从阀体上取出。
Remove the handle from the stem by pulling upward and away from the body.
在管道上安装调节阀，将阀体上的箭头指向水流方向。
Install regulator in the line with the arrow on the body pointing in the direction of flow.
阀体应该钻孔和攻丝用于在顶部和底部外壳的压力连接。
Valve body shall be drilled and tapped for a pressure connection on top and bottom of the housing.
(调整)模铸在阀体的外部，表示用于组装的开口端口。
ADJ externally molded onto the body to indicate the open end used for assembly.
该蝶阀采用阀体同质材料加工成密封圈，采用电或气传动。
The butterfly valve using the same materials as seals, the use of electric or gas transmission.
透平进汽阀的气动稳定性是导致进汽阀阀体振动的主要原因。
Aerodynamic stability of turbine inlet valve is the main reason of the vibration of valves.
阀体和内件由高温合金钢制造，其特点是高温下耐磨和阀体寿命长。
The valve body and internals are made from high-temperature alloy which features high-temperature abrasion resistance and long service life.
积极的机械推力驱动阀塞进入阀体阀座馁，确保紧密双向管路密封。
Positive mechanical thrust drives plug into body seats to ensure tight bi-directional line seal.
介绍了阀体与接管焊接的焊缝技术要求、执行标准、检验内容及合格指标。
Introduce welded seam specification, standards performed, inspectation items and acceptable index for welding of body and joint pipe.
阀塞和阀体阀座表面先由沉积层形成，然后经过机加工制成镜面光洁度表面。
The facing is deposited on the plug and body seats and is then machined to a mirror-like surface.
阀体采用粉体环氧树脂涂装，可防止阀体的腐蚀及生锈，并可用于污水系统。
The body of valves is printed by powdered epoxy, can be prevent the corrosion and rusting, can be used to sewage system.
阀体采用粉体环氧树脂涂装，可防止阀体的腐蚀及生锈，并可用于污水系统。
The body of valves is printed by powdered epoxy, can be prevent the corrosion and rusting, can be used to sewage system.
应用推荐