大约有一半的铸铝工艺是高压模铸(HPDC)，在这种工艺中，通过压力将液态铝合金注入钢模，或模具。
About half of all aluminium castings are made using high-pressure die-casting (HPDC), in which a molten aluminium alloy is injected under pressure into a steel mould, or die.
他们艰难地生活着，冒着被绞死的危险，但是他们却像斗鸡般地吃喝着，而一旦一次航行结束了，他们口袋里成百的钢蹦儿就会换成成百上千的金铸。
They lives rough, and they risk swinging, but they eat and drink like fighting-cocks, and when a cruise is done, why, it's hundreds of pounds instead of hundreds of farthings in their pockets.
然而，防腐蚀铸层与钢脚间的结合不良将削弱锌的阳极保护作用。
However the poor bond between the anticorrosion casting coating and steel-foot would weaken the anodic protection of zinc.
感觉结实的，铁铸的或变黑的钢。
铸坯裂纹漏钢在连铸生产过程中经常发生。
The billet crack breakout would take place often in the process of continuous casting.
连铸水口堵塞的类型有四种，即脱氧产物、固态钢、复杂氧化物及反应产物。
There are four types of the cloggings in the submerged nozzle for continuous casting. They are, namely, deoxidation products, solidified steel, complex oxides and reaction products.
文章对唐钢连铸中间包钢水等离子加热技术进行了较系统的论述，研究了中间包结构和炉渣等对加热效果的影响。
This paper systematically discusses the technology of plasma tunish heating molten steel in tunish and also the influence of tunish structure and the slag on heating efficiency.
软接触结晶器电磁连铸方法是一项新的连续铸造技术，主要用于钢的连续铸造过程，目前已取得了较快的进展。
Soft contact electromagnetic continuous casting is a new type method for continuous casting technique which main used in the cast of steel and have been developed greatly now.
研究采用铸渗法制备三元硼化物硬质合金覆层钢基材料。
The preparation of ternary boride hard alloy cladding layer on steel substrate is studied.
结果表明：用冶炼高钛渣的副产半钢生产球墨铸管在工艺上是可行的。
As a result, it is feasible that making of ductile iron pipe use of semi-steel.
软接触结晶器电磁连铸方法是一项新的连续铸造技术，主要用于钢、铝的连续铸造过程，目前已取得了较快的进展。
Soft contact electromagnetic continuous casting is a new type method for continuous casting technique which main used in the cast of steel, aluminum and have been developed greatly now.
发动机壳体为一个其一端为密封的钢铸圆柱缸体，另一端则为敞口的喉道及喷管。
The motor case is a steel cylinder closed tight at one end. the other end is the open throat and nozzle.
该铸态贝氏体钢通过合金化和控制冷却速度的方法，不需热处理而在铸态下直接得到贝氏体组织和所需性能。
The new bainitic steel formation and its required characteristics were obtained directly in the casting phase without any heat treatment, by the way of alloying and controlled cooling.
应用流场计算软件PHOENICS及水力模型，模拟了方坯连铸结晶器内钢液的流场和流动分布。
Using flow field software PHOENICS and water model, this paper describes the flow field of molten steel in continuous casting billet mold.
铸坯内产生针孔气泡缺陷的原因是钢液脱氧不良，产生大体积气泡缺陷的原因是铸机浇注过程中氩气流量过高。
The defects on pinhole bubble formed in slabs result from badness deoxidization, and the defects on large volume bubbles formed in slabs result from the high flux of argon during casting.
给出了钢精炼和连铸过程中若干典型的钢液流动驱动与控制工艺过程及相关现象研究进展。
Some typical technology and their current advancement associated with the drive and control of molten steel flow are illustrated.
因此，根据建立的计算模型得到了薄带连铸304不锈钢的变形抗力数学表达式。
Therefore, the mathematic expression of deformation resistance of 304 stainless steel strip continuous casting was obtained according to the model built.
初步研究发现，对由连铸然后经控制轧制生产的管线钢层状撕裂几乎总是沿中心线偏析带发生。
It is found that the 'delamination always takes place along the centerline segregation band in pipe-line steel produced by continuous casting and then controlled rolling.
在动载三体磨粒磨损条件下，试验研究了冲击载荷的变化对铸态复相耐磨钢动载磨粒磨损特性的影响。
The influence of varying impact energy on wear resistance of dual phase cast steel has been investigated under impact three body abrasion.
介绍了连铸粘结性漏钢产生的机理和过程，以及宝钢利用人工神经网络技术建立的一套新的漏钢预报系统。
This article presents the mechanism and process of sticking breakout occurring, as well as the newly built prediction system for sticking breakout in Baosteel based on neural network technology.
所研究的铸态贝氏体钢是通过合金化和控制冷却速度的方法在铸态下直接得到贝氏体组织的，不需热处理即可获得所需的组织和性能。
The as-cast bainite steel studied in this paper could obtain bainite directly in the as-cast condition through alloying and controlling the cast cooling rate without heat treatment.
高铝钢连铸过程中，钢渣反应将导致连铸保护渣成分和性能发生较大的变化。
During continuous casting of high aluminum steel, composition and properties of mold fluxes change obviously due to the slag-steel reaction.
文章主要介绍了采用钢轨钢连铸坯热送热装工艺生产钢轨组织的变化和所能达到的各项性能指标。
This paper introduces the change of microstructure and properties of the rolled rail steel of CC bloom in hot charging.
本文就薄板坏连铸连轧生产热轧TRIP钢的可行性进行了分析和讨论。
In the present article, the feasibility of the production of hot rolled TRIP steels using TSCR process was analyzed.
本文介绍了珠钢连铸结晶器液位控制系统的配置，控制方式和控制算法，以及液位控制原理。
The article mainly describes caster mould level control system in Zhujiang Steel including its configuration, control mode, control arithmetic, as well as mould level control principle.
分析了连铸薄板坯表面纵向裂纹的产生原因，结合通钢薄板坯生产实际情况，提出了改进措施。
The causes of surface longitudinal cracking were analyzed. Countermeasures were put forward based on the production practices of thin slab casting and rolling at Tonghua Steel Co.
天钢第二炼钢厂供氧系统供氧强度低，冶炼周期长，限制了铸坯产量的提高。
Because of the low oxygen blowing intensity, long smelting period and low billet yield, the oxygen system is rebuilt in No.
众所周知漏钢是连铸生产中最为严重的生产事故，造成巨大的直接和间接经济损失。
It is well known that breakout is the most serious accident in casting, it will cause a huge direct or indirect economic loss.
完成了连铸和模铸LZ50车轴钢疲劳裂纹扩展试验，得到了两类LZ50车轴钢的疲劳裂纹扩展曲线。
The fatigue crack propagation testing were completed for CT specimens of LZ50 axle steels with continuous casting and mould casting.
完成了连铸和模铸LZ50车轴钢疲劳裂纹扩展试验，得到了两类LZ50车轴钢的疲劳裂纹扩展曲线。
The fatigue crack propagation testing were completed for CT specimens of LZ50 axle steels with continuous casting and mould casting.
应用推荐