通过304不锈钢的退火试验，获得了综合性能较高的热处理工艺参数，能够为生产提供一定的参考作用。
Through the annealing test of 304 stainless steel, high performance access to a comprehensive process of heat treatment parameters, to provide for the production of some reference value.
钢的热处理操作主要有三种，即：淬火，回火和退火。
There are three main operations in the heat treatment of steel: hardening, tempering and annealing.
钢的热处理操作主要有三种，即：淬火、回火和退火。
There are three main operations in the heat treatment of steel: hardening tempering and annealing.
退火工艺的组成为把钢加热到一定温度并保持一段时间，通常再缓慢冷却。
The process of annealing consists of heating the steel to an elevated temperature for a definite period of time and, usually, cooling it slowly.
铬镍不锈钢在退火状况下通常是无磁性的，在冷加工之后，有的会有磁性的。
Chromium nickel stainless steel is usually non - magnetic in the annealed state, some of which are magnetic after cold working.
高于此点，由于超过共析点钢完全由珠光体和退火状态的渗碳体组成，硬度增加并不多。
Above this point the hardness can be increased only slightly, because steels above the eutectoid point are made up entirely of pearlite and cementite in the annealed state.
钢的热处理工序包括硬化、回火、退火和表面硬化。
The procedures of heat treatment of steel include hardening tempering annealing and case hardening.
退火。退火工艺的组成为把钢加热到一定温度并保持一段时间，通常再缓慢冷却。退火是为了产生均匀化从而建立起有一致的特有性质的标准均匀化组织。
Tool steel is generally purchased in the annealed condition. Sometimes it is necessary to rework a tool that has been hardened, and the tool must then be annealed. For.
研究了烘烤温度、烘烤时间和预拉伸应变量对罩式炉退火工艺生产的各向同性钢的烘烤硬化性的影响，并与力学性能相当的冷轧烘烤硬化钢进行了对比。
The effects of baking temperature, baking time and prestrain on the bake hardenability and dent resistance of isotropic sheet steel and BH sheet steel produced by batch annealing were studied.
经过退火及冷加工的热轧不锈钢棒材，其表面质量更高，强度也更高。
Hot rolled stainless steel bars that are annealed and cold worked to produce a higher surface quality and higher strength.
长时间扩散退火可有效地提高粉末锻造钢的韧性。
Toughness of powder forging steel can be increased efficiently by diffusion annealing in longer time.
本文介绍了高速钢快速软化退火的三种方法。这些方法具有节能、高效、周期短、成本低等特点。
This paper introduces three methods of rapid softening and annealing for high speed steel. There are many advancetages of energy-saving, short cycle and low cost.
冷轧没有经过退火的铬镍不锈钢，外表洁白有反光。
Cold rolled stainless steel, stainless steel, white and reflective.
本文介绍国产A508-3钢在不同的淬火、回火和退火条件下的热处理实验的某些结果。
This paper presents some results of heat treatment experiments of A508-3 steel at different quenching, tempering and annealing conditions.
各种退火制度对冷拉钢脆性劈裂的影响较小。
The effect of various annealing systems on the splitting of cold-drawn steel rod is very little.
在通常所说的退火的热处理过程中，我们把钢加热到临界温度以上，再让它慢慢冷却。
In the process known AS annealing, we heat the steel above the critical temperature and permit it to cool very slowly.
显微组织分析表明，含钛钢中生成了钛化物相，并且随着退火温度的提高，钛化物析出量增多。
Analysis on the microstructure shows that precipitation of compound containing titanium was found in the steel, and its amount increases with the elevation of annealing temperature.
介绍了无涂层电工钢冲片叠片成型后的电机定子和转子在罩式炉内进行退火和发蓝处理一次完成的新工艺及装置。
A new technology and equipment of annealing and bluing for finished stator and rotor of uncoated cold-rolled electric steel lamination in bell-type hytrogen furnace was introduced.
未经扩氢退火的电渣钢大锻件经超声波检验，未发现白点缺陷。
Ultrasonic testing shows on flake defects in theheavy forgings of ESR steel without any diffusion annealing.
介绍不锈钢退火酸洗处理线自动控制系统的组成，控制思想和软件。
To introduce the configuration, control method and software of the automatic control system for stainless steel annealing and pickling line.
介绍了无涂层电工钢冲片迭片成型后的电机定子和转子在罩式炉内进行退火和发蓝处理一次完成的新工艺及装置。
A new technology and equipment of annealing and bluing for finished stator and rotor of uncoated cold-rolled electric steel lamination in bell-type hydrogen furnace was introduced.
研究了锻造后的冷却速度对T10钢等用球化退火加热温度和保温时间的影响。
The influences of cooling rate after the forge on the heating temperature and time of apheroidized annealing of steel T10 was studied.
明确了H13钢退火后硬度的高低与碳化物粒子的大小、相对量及碳化物的类型的依赖关系。
The results show that the hardness of H13 steel after annealing depends on size, relative amount and type of carbide.
本文研究了非正常原始组织的轴承钢，退火后的组织及其评级问题。
In this paper the annealed structure and its grade of bearing steel with abnormal original structure have been studied.
为了满足市场对冷轧薄板钢需求量的不断增加和连续退火工艺要求，超低碳钢生产也在不断增加。
To meet uninterruptedly increasing in the demand for the cold rolled steel sheets and to meet the technological demand of continuous annealing, the production of ultra-low carbon steel is increasing.
研究了高速钢轧材在台车式电阻炉中退火加热过程中，各因素对脱碳的影响。
The effects of various factors on decarburization of high speed tool steel annealed in bogie hearth electric furnace were investigated in this paper.
介绍冷轧板带退火工艺的特点，探讨柳钢冷轧板带退火的设备选择。
The characteristics of cold-rolled strip annealing practice have been introduced, and the equipment selection of old-rolled strip annealing has been discussed.
介绍冷轧板带退火工艺的特点，探讨柳钢冷轧板带退火的设备选择。
The characteristics of cold-rolled strip annealing practice have been introduced, and the equipment selection of old-rolled strip annealing has been discussed.
应用推荐