我们是专门供应塑胶钢模的绩优厂商。
这是小男孩的包裹不一钢模。
管片钢模是盾构管片生产的关键性因素。
Steel moulds are vital for the production of the segments of shield tunnels.
板模板采用组合钢模，在组拼时模板缝间夹海绵条。
Combined steel form will be used for slab form, and sponge strip shall be used for the form joint during matching.
而沸腾钢从冶炼直至钢模中、韧性、硅铁或铝来脱氧。
The boiling steel from smelting until the steel mold, toughness, ferrosilicon or aluminum deoxidation.
同时，更新我们所有的挤出(31一钢模)的生产状态。
Also, update us the production status of all the extrusions (31 dies).
一些汽车在火焰，和23个人破坏性的碰撞一钢模中被卷入。
Several cars are engulfed in flames, and 23 people die in the devastating collision.
但是相对于钢模，其强度硬度较低、耐蚀耐磨性差，限制了应用。
However its intensity and hardness was low, wear-resisting and anticorrosion is poor, which is opposite in the steel, the application has been limited.
在庙宫水库排沙洞的衬砌施工中使用了针梁式混凝土衬砌钢模台车。
We have used needle beam telescoping steel form in the Mao-Gong reservoir sediment tunnel in the concrete lining.
六片组合模、不锈钢模具、铆钉模具更是精诚质量优为稳定的产品；
Six combination screw mould, stainless steel mould and rivet mould are products with more stable quality.
以聚氨酯橡胶代替通常钢模中的凹模或凸模是比较有效的方法之一。
It's one of best methods to use polyurethane rubber rather than usual cavity or core in steel die.
结合工程实践，介绍了小钢模拼装成大模板用于短肢剪力墙的施工方法。
Based on actual engineering, construction method of large steel formwork for short shear wall is introduced in this paper, which is assembled by small steel formwork.
采用活塞钢模，室温下利用徐州市夹河煤和生活垃圾制备出了垃圾衍生燃料。
The refuse derived fuel (RDF) was made from mixture of Xuzhou Jiahe coal and municipal domestic refuses with a steel piston mold under room temperature.
以硅橡胶材料制作的芯模与钢模组合使用制备碳纤维复合材料制件，应用效果较好。
The core mold made of thermal expansion silicon rubber is used with steel mold to mold CF composite products with good result.
另一是用钢模比拟法对扁挤压筒预紧装配过程进行模拟，获得了挤压筒内孔型腔变形规律。
On the other hand, simulate the interference fitting process to get the deformation distribution of the mould cavity by steel mould correlation method.
可用于钢模、木模、混凝土胎模、干模或湿模的现浇混凝土施工或蒸养混凝土制品脱横用。
Can be used in steel form, block, concrete tire mold, dry or wet modulus of mould construction of cast-in-situ concrete products or steamed keep off the use.
大约有一半的铸铝工艺是高压模铸(HPDC)，在这种工艺中，通过压力将液态铝合金注入钢模，或模具。
About half of all aluminium castings are made using high-pressure die-casting (HPDC), in which a molten aluminium alloy is injected under pressure into a steel mould, or die.
工具在重的打击之下操作，举例来说令人生气一钢模为门闩的感冒-标题，不能穿越是-变硬。
Tools operating under heavy blows, e. g. upsetting dies for cold-heading of bolts, must not be through-hardened.
目前公司在对铝翻砂工艺与钢模浇注技术进行改良后，独家采用铝压铸制造和环保型喷塑工艺。
After improving the aluminum foundry and steel casting technology, our company uses the aluminum die-casting manufacturing technology and enviroment-friendly spray exclusively.
直接利用激光快速成型的原型树脂模，结合陶瓷型精密铸造技术，制得了高精度、低表面粗糙度、高使用寿命的钢模具。
The steel dies with high dimensional accuracy, low surface roughness and long service life have been quickly produced by using prototyping resin molds as patterns of ceramic investment casting.
成形极限图通常是通过钢模胀形试验测得，实际测量的成形极限图与ASAME自动应变测试分析系统模拟计算的成形极限曲线吻合较好。
FLD is usually measured with swell test in rigid die. The tested FLD is good fit that one measured by analogue computer in ASAME (Automated Strain Analysis and measure Environment).
工具钢的一些应用有钻头、深压模、底刃、冲床、挤出模及切割刀具等。
Some applications of tool steels include drills, deep drawing dies, shear blades, punches, extrusion dies, and cutting tools.
主要的铸锭设备有盛钢桶和钢锭模。盛钢桶是用来盛装从炼钢炉放出的钢液的容器。
The major equipments are the ladle and the mould. a ladle is a container to hold the molten steel tapped from the steel making furnace.
所以，在钢锭模内析出的气体没有沸腾钢多，但又在钢锭头产形成足够的气泡抵消大部分钢的收缩。
So less gas is. given off in the mould than with rimming steel, but enough bubbles form at the top of the ingot to counteract most of the shrinkage.
钢液在模内不受搅动平稳上升。
结构：辊模由钢筒芯构成，即便覆盖有互交式青铜和塑料模，也能避免各种弯曲变形。
Structure: by the cylinder roller mode, even is the core of bronze and mutual into plastic mould, also can avoid all sorts of bending deformation.
主要介绍了不锈钢球形响壶盖的落料、拉伸、挤边复合模的详细结构、模具工作过程、工艺分析。
Mainly introduced the detailed structure and working process and the technology analysis of the blanking-drawing-extruding compound die for the stainless steel whistle pot cover.
主要介绍了不锈钢球形响壶盖的落料、拉伸、挤边复合模的详细结构、模具工作过程、工艺分析。
Mainly introduced the detailed structure and working process and the technology analysis of the blanking-drawing-extruding compound die for the stainless steel whistle pot cover.
应用推荐