由地形坡度引起的影象配准误差及目标区最佳尺寸分析。
The analysis of registration error from terrain slope and the best target size.
实验结果表明算法对噪声和配准误差具有很好的鲁棒性。
The results justify the robustness of the proposed methods against image noise and registration errors.
实验结果表明，这种方法对噪声和配准误差都有一定的鲁棒性。
The experiment results show this method is robust to noise and misregistration error.
实验统计结果表明，该方法的配准误差约为系统测量误差的66%。
The statistical results in experiments show that the registration error of this method is about 66% of the system measuring error.
高分辨率遥感影像波段间配准误差是影响影像质量及其应用精度的重要因素之一。
Being one of the important factors responsible for image quality, the band to band registration error of high resolution imagery affects considerably the application precision of remote sensing.
文中还采用平滑滤波器解决了在两幅图像镶嵌出可能由于累积配准误差而出现明显的条缝。
The accumulated misregistration errors may cause a visible gap between the two images. A smoothing filter is introduced for removing the visible artifact.
而对于高分辨率遥感图像的变化检测，面临的突出问题是对配准误差的敏感性和人工环境下地形的复杂性。
The most serious problems for change detection on high-resolution images are the sensitivity to registration and the complexity of terrain.
为了减小配准误差对盲超分辨率重建的影响，提出了一种影像配准和盲超分辨率重建联合处理的模型与方法。
In this paper, a new joint Maximum a Posterior (MAP) formulation was proposed to integrate image registration into blind image Super-Resolution (SR) reconstruction to reduce image registration errors.
低分辨率图像的信噪比(SNR)和图像之间的配准误差对超分辨率重构效果的影响是该技术应用在遥感领域的瓶颈。
The influence of Signal-to-noise ratio (SNR) of low-resolution images and registration error among them on the super-reconstruction of images is the bottle-neck in the field of remote sensing.
设雷达网中某一部雷达无系统偏移误差，将其多雷达组对于该雷达进行相对配准。
One of the netted radars is assumed to have no system bias errors, the relative bias error registration are implemented for other radars.
这些误差必然会影响图像配准、合成等。
The error has an effect on image registration and synthesizing .
而弹性近似法充分考虑了整体平滑性的要求，对定位有误差的标志点约束的图像配准更为优越。
Another method is thin plate spline elastic approximation, which takes the overall smoothness of the whole image into account, hence it is better when errors of feature points exist.
基于配准，通过运动分析首次实现了流速的无原理误差测量。
Through motion analysis and based on registration we achieve velocity measurement without principle errors for the first time.
仿真表明两种算法能有效地对雷达系统误差进行估计，尤其是当系统偏差发生变化时，配准效果明显优于实时质量控制(RTQC)配准算法。
Simulation results show that the proposed algorithms are effective and are superior that of the real time quality control (RTQC) algorithm for the varied system errors.
通过误差来源的分析和误差模型的建立，提出了一种车辆导航中gps定位测量与数字地图实时配准的地图匹配算法。
According to the given source and mathematic model of matching error, a algorithm for real time matching of GPS positioning results and digital maps is put forward.
为了使融合结果更加准确可靠，提出了基于无偏转换的雷达误差配准算法。
For the better optimization of fusion results, the radar registration algorithm based on unbiased transformation was brought forward.
相邻帧配准差分去除恒星方法，在处理16位灰度图像时，由于高亮度恒星的插值误差大于目标灰度与背景之差，导致差分不能有效去除恒星干扰。
Registration and difference can't exclude stars when processing the 16-bit gray images because interpolation error of high light star is larger than the difference of target and background.
提出了一种新的基于合作目标的动基座传感器误差绝对配准方法。
A novel bias estimation method for solving maneuvering sensor bias correction problems based on cooperation target is proposed.
结果仿真结果表明：平均误差由配准前的40像素降到了配准后的1.5像素；
Results Simulation results showed that the residual registration errors on average were decreased from 40 pixels before registration to 1.5 pixels after registration.
该算法可以有效地实现异类传感器之间的误差配准，同时估计目标的运动状态和传感器的系统误差。
Registration for heterogeneous sensor can be realized effectively, track of target and sensors' systematic errors can be estimated simultaneously.
目前的基于多项式、正交多项式和加权正交多项式的图像配准方法是以误差平方和为度量标准的。
To correct the image distortions in orthopedic surgery based on the Xray fluoroscopic image, an orthogonal polynomial and a weighted orthogonal polynomial methods are proposed.
对标准图像与待检图像分色后，对应色的灰度图像进行配准，最后利用图像固有的信息和配准信息获得套印误差。
The standard image and the images collected from printings are color-separated, then each pair of images with the same color is matched;
针对多点成形件成形误差检测中的三维数据配准问题，提出了一种用两步法将CAD模型数据和三维测量数据点全局配准的方法。
In this paper, a new method for the global registration of the CAD modeling data to the 3d measured data is presented.
针对多点成形件成形误差检测中的三维数据配准问题，提出了一种用两步法将CAD模型数据和三维测量数据点全局配准的方法。
In this paper, a new method for the global registration of the CAD modeling data to the 3d measured data is presented.
应用推荐