方法：采用综合造模法。
方法：将大鼠随机分5组，采用乙醇和脱氧胆酸钠复合造模法。
Methods:The Wistar rats were randomly divided into 5 groups. The CAG model was made by using the alcohol method and deoxycholic acid.
容量最大的造模法，通过高压的作用材料从外部加热室通过铸口、流道或浇口进入闭式压膜室。
The highest volume molding method, in which the material is forced from an external heated chamber through a sprue, runner or gate into a cavity of a closed mold by means of high pressure.
方法：采用大鼠静脉血栓形成造模法，颈总动脉-颈外静脉血流旁路法，小鼠静脉注射胶原蛋白-肾上腺素造成血栓形成等模型。
Methods: a rat venous thrombosis modeling method, common carotid artery-jugular vein blood flow in the bypass method, intravenous injection of mice with collagen-adrenaline causing thrombosis model.
通过采用边界元法对高线轧机压下垫块改造模型进行力学分析，开发设计一种适合测量高线轧机油膜轴承动态载荷特性的简易装置。
The screwdown block is improved by mechanics analysis with boundary element method, and a simple device is designed for dynamic load of oil film bearing used in high-speed wire rolling mill.
为了保证高校胜任力特性构造模型的准确性，本研讨又应用了问卷法入行了探索性和验证性因素剖析。
In order to guarantee the accuracy of the university competence characteristic structural model, this research utilized the questionnaire law to carry on exploring and confirmatory factor analysis.
采用特种砂v法铸造工艺获得了良好表面精度和尺寸精度的铸造模具。
The fine surface quality and dimensional accuracy cast hot work die was obtained by special sand V method casting technique.
目的探讨用肾上腺素法进行血瘀证动物模型造模时的最适浓度。
Objective To investigate the most appropriate drug concentration in making animal model of blood-stasis with adrenalin.
采用结扎双侧颈总动脉法造模，各观察组用脑通滴鼻液滴鼻，对照组用维脑路通腹腔注射。
Make model by ligating bilateral common carotid arteries, apply Naotong Dibi Liquid to the observation groups by dripping nose, Weinao Lutong to control by abdominal injection.
方法用四动脉阻断法造模，观察背侧海马神经元的超微结构；
Electron microscope was used to observe the ultramicrostructure of dorsal hippocampal neurons.
应用带有力学调控系统的各向异性骨再造模型结合有限元法，进行妇女骨质疏松过程及运动防治的模拟。
The processs of female Osteoporosis and its prevention by Physical activity were simulated using anisotropic bone remodelling model with mechanostat combining with finite element method.
前言：在铸造模拟中，目前流动前沿的难题处理上，用得较多的有两种方法：V OF法和守恒标量法。
There is two methods used most in the casting process simulation to determine the flowing front at present: the VOF method and the conservation scalar quantity method.
鼻腔滴注法建立小鼠肺部肺炎克雷伯菌感染模型，比较不同接种剂量组死亡情况，确定最佳造模剂量；
To establish the mice pneumoniae model of Klebbsiella pneumoniae infection by nasal and compare the death of different inoculation doses in order to determine the optimum dose.
造模方法主要有两种：一种是单用“慢性束缚法”，另一种是复合慢性束缚及冷水游泳加进食时电刺激。
There are two methods in model preparation: one is "chronic bondage". Another is the complex of chronic bondage and swimming in cold water, accompanying with electrical stimulation while eating.
方法SD大鼠采用肾动脉狭窄法造模，6周后制成肾性高血压模型（RHR）。
METHODS SD rats were turned into renovascular hypertensive rats(RHR) by chronic partial occlusion of left renal artery after 6 weeks.
方法SD大鼠采用肾动脉狭窄法造模，6周后制成肾性高血压模型（RHR）。
METHODS SD rats were turned into renovascular hypertensive rats(RHR) by chronic partial occlusion of left renal artery after 6 weeks.
应用推荐