研究分析了不同的切削速度及进给量对叶轮叶片加工的表面粗糙度的影响。
The influence of different cutting speed and feed rate on the roughness of vane's finished surface was investigated and analyzed.
锯条切割速度及进给力图表提供了合适的锯条速度和进给力参数，使锯条能发挥最佳性能。
The blade speed and feed charts provide proper blade speed and feed parameters for optimum performance of the blades.
经实际生产验证，该伺服进给系统能准确地实现伺服运动，满足加工过程要求的系统定位精度、响应速度及稳定性。
The practice result shows that this servo-feed system can realize servo moving accurately, and can meet the system position accuracy, response speed and stability required by the machining process.
研究结果表明，对于微晶玻璃等脆性材料，其表面粗糙度主要与砂轮的平均磨粒尺寸、砂轮速度、进给量及磨削深度等因素有关。
It is showed that the surface roughness is mainly related with the average grain size and feed per wheel revolution for the brittle materials such as single crystal silicon.
全新电源系统，针对大面积及深孔加工，电脑可选定二段伺服进给速度，加工性能优异并可保持放电精密度。
Newly designed power supply system. While in machining big surface and deep hole, the computer provides two steps servo feed for superior machining quality and discharge accuracy.
前言： 通过试验，找出了切削深度、切削速度、每齿进给量等切削用量及切出角影响面铣刀寿命的规律。
Tests are conducted to find the rules how such cutting parameters as cutting depth, cutting speed and feedrate per blade as well as the cutting angle affect on the life of face mill.
同时对不同的径向和轴向进给速度对径轴双向复合轧制过程中轧制力，直径增长速率及温度分布的影响进行了系统分析，并进行了相应的实验验证。
Influences of different radial and axial feeding speed on the radial and axial rolling force, growth rate of diameter and temperature have been systematically analyzed and proved by trials.
通过试验，找出了切削深度、切削速度、每齿进给量等切削用量及切出角影响面铣刀寿命的规律。
Tests are conducted to find the rules how such cutting parameters as cutting depth, cutting speed and feedrate per blade as well as the cutting angle affect on the life of face mill.
利用有限元法证实了内高压成形三通管的可行性，给出了不同轴向进给速度下零件的壁厚及应变分布，并就轴向进给速度对成形的影响进行了分析。
The feasibility of hydroforming tri-branch tube is proved by FEM. The corresponding thickness and strain distribution of different axial feed velocity on the simulation is analyzed.
本文在高速滚齿机上，利用遥测应变仪，测定了工件材料，进给量，切削深度，切削速度，齿轮齿数及螺旋角等对力矩的影响，并得出径节为8时的力矩公式。
This paper presents the information of the effect, measured with a tele-strain-meter, of work material, feed, cutting speed, depth of cut, number of teeth and helix Angle etc.
本文在高速滚齿机上，利用遥测应变仪，测定了工件材料，进给量，切削深度，切削速度，齿轮齿数及螺旋角等对力矩的影响，并得出径节为8时的力矩公式。
This paper presents the information of the effect, measured with a tele-strain-meter, of work material, feed, cutting speed, depth of cut, number of teeth and helix Angle etc.
应用推荐