对此轮廓线逐点计算曲率得到曲率线。
After smoothing the curve, the curvature of every point of the contour is calculated.
传统图象匹配算法利用相关法进行逐点计算，计算量大且做了许多无用功。
Normalized pattern matching is based on correlation and operated point by point with a large quantum of operation and low efficiency.
采用常规测井解释方法逐点计算单井剖面中各小层的渗透率往往很难达到精度要求。
It is very difficult to calculate this parameter from point by point conventional log interpretation for the layers in a single well section.
然后逐点计算局域态密度发现，在实空间准束缚态是一个非常局域化的效应，离开缺陷即迅速衰减。
The corresponding image of local density of states in real space shows a highly localized state around the defect.
计算结果表明渐近波形估计技术与矩量法结合可以逼近矩量法逐点计算的结果，且计算效率大大提高。
The numerical results are in good agreement with the results achieved by the method of moments at each frequency or any incident angle, while the computational efficiency is considerably improved.
第一种是适用于叶片骨线为任意曲线的逐点计算法；第二种是适用于叶片骨线为有规则线段的骨线绘图法。
The first one applies to point by point calculation of blade spine consisting of a random curve and the second one is for blade spine consisting of regular line sections.
有理参数多项式曲面的快速逐点生成算法在计算机图形学中有重要的应用。
The fast point-by-point algorithm for generating rational parametric surfaces has important application in computer graphics.
它是先在横断面图上量得边桩的大致位置，再通过计算逐点逼近设计的边桩的。
The approximate location of the side pile should be first measured in the cross section map, then it will be approached to the designed side pile spot by spot through calculation.
基于计算机数控系统中逐点比较法的基本思想，提出一种新的插补算法。
Based on the basic principle of point by point comparison, a new interpolation algorithm is presented.
导出了像逐点的斜率计算公式；
算例表明，连续崩溃点法与逐点使用连续潮流方法计算崩溃点的方法相比，计算效率得到明显提高。
Simulation result shows compared with calculating several collapse points by repeatedly use continuous power flow calculations, the effectiveness of calculation by this method will be improved.
文中首先对用于有效值计算的逐点积分法与浮点开方算法进行了论述，并在此基础上介绍了系统的检测原理。
Firstly, the testing principle of this system is introduced on the basis of discussabout point-by-point integration method and floating-point evolution.
确定了以逐点积分法作为电流有效值的计算方法，建立了以80c196KC单片机为中心控制器件的软件、硬件系统。
The calculation of spot welding current is determined by the way of point-by-point integration, the software and hardware system is constituted based on 80c196kc single chip computer.
基于计算机数控系统中逐点比较法的基本思想，提出一种新的插补算法。
According to the basic mechanism of point to point comparing method, a new interpolating recurrence algorithm is proposed.
目的建立逐点回归计算方法。
Objective To establish a method of regression computation by the level of signal.
目的建立逐点回归计算方法。
Objective To establish a method of regression computation by the level of signal.
应用推荐