这款配件由平行丝线和外锥组成。连接焊接在椎体上。材质为316不锈钢。
This fitting design consists of parallel threads and an external cone. The connection seals on the cone. Stocked in 316 Stainless Steel material.
轮子旋转时需要承受巨大的和不断变化的压力，所以要使结构更坚固，钢的部分要用螺栓连接，而不是焊接在一起。
The wheel would need to withstand immense and constantly changing stresses as it rotated, so to make the structure more robust, the steel sections were bolted rather than welded together.
这时你可能需要一些焊接项目，修复那些坏死的线路连接。
You might have to whip out a soldering item and deal with some bad connections.
焊接和连接这些晶体管需要好几辈子。
它是一种利用焊条与工件之间电弧产生的热量熔化焊条和母材而将被焊工件连接起来的焊接方法。
This welding process joints work pieces by melting the electrode and the base metal with the heat from the electric arc between the electrode and the work piece.
将电弧焊设备上的接地连接尽可能近地连接到将要焊接零件的焊接点上。
Connect the ground connection of the electric arc welding equipment as near as possible to the welding point on the part to be welded.
使用联接器，夹子，螺钉，螺栓，水泥或焊接，钎焊和焊接设备连接管件。
Join pipes using couplings, clamps, screws, bolts, cement or soldering, brazing and welding equipment.
但9天之后一个简单的电气连接因为焊接不良过热造成伤害。
But nine days later a single electrical splice overheated because it had been badly soldered, and disaster struck.
焊接，钎焊，用水泥涂抹，焊锡和螺纹接头，使其连接至管道，从而制造管道系统截面。
Weld, braze, cement, solder and thread joints to join pipes and fabricate sections of piping system.
应采用低氢焊条焊接厚钢板与铸钢件和高强度板间的连接。
Low hydrogen electrode to be used for welding thick steel plate to casting and high tensile plates.
将转接件分别焊接在埋件上及工字钢上，然后将立柱用螺栓与转接件连接起来。
Weld switchover pieces separately on embedment and I-steel, and then connect the mullion with bolts and switchover pieces.
钢柱通过螺栓与埋板连接，校准后进行焊接。
Steel columns are connected via bolts and cast-in plate and will be welded after calibration.
在这一阶段，如果存在问题，可以很容易地改造焊接的连接点。
At this stage, it's easy to remake a solder connection if there is a problem.
管道安装工作包括：预制加工、安置、对准、焊接和连接。
Piping erection work include: prefabrication, placing, aligning, welding and bolting.
当开关柜完全装配好时，可用螺钉或焊接将其和基础框架连接在一起。
When the switchgear has been properly assembled, fasten the panels to the foundation frame by welding or by using adequate bolts.
连接层可用冲压成型的钢质菱形网，用气体保护焊接方法点焊于钢板上。
Layer can be used to connect steel stamping forming diamond-shaped network, with gas shielded welding spot on the plate.
使用拼接工具，相关电气设备和工具接头，焊接和绝缘导线和相关的接线工，从而连接到输配电网络。
Splice, solder and insulate conductors and related wiring to connect power distribution and transmission networks using splicing tools, related electrical equipment and tools.
使用大量的焊接通量，以确保完美的连接。
Use plenty of soldering flux to ensure a perfect connection.
如果阀体的材料是可以焊接的，但膨胀系数差异很大，或者工作温度的变化幅度范围较大，螺纹连接部必须进行蜜封焊。
If the valve body material can be welded, but very different thermal expansion coefficient, or changes in operating temperature range of a larger thread junction closure weld must be honey.
本文提出了用真空固态热扩散焊接工艺连接金属分层板的方法。
A process connecting metallic slice sheet by diffusion welding is also put forwarded in this dissertation.
这种阀门应该具有焊接（-US）、螺纹（-UT）、PEX或CPVC等连接端口可供选择。
The valve shall be provided with solder (-US), threaded (-UT), PEX or CPVC connections.
论述了激光焊接连接防护罩和螺母的优越性。
The superiority of the connection of nut with protection by laser welding is expounded.
将提供各种形状的管件以不同连接形式焊接与切割以实现自动化、程控化的计算方法。
This paper provides calculating methods to accomplish automatic and program-controlled welding of all-shaped pipes in different connecting forms.
用焊接方法连接的接头称为焊接接头，它由焊缝、熔合区、热影响区及其邻近的母材组成。
The joint which is connected by welding method is called the welding joint, which is composed of welding seam, fusion zone, heat affected zone and its adjacent base metal.
一个良好的电气连接并焊接材料必须建立。
A good electrical connection to the material to be welded must be established.
引下线的连接应焊接，采用共用地网和一点接地方式接地等结论。
Down -conductor system connection should be welded, and the conclusion of common earthing system and adoption single earthing has been drawn.
非防爆区域内穿线管连接处两端，应焊接跨接线，或用接地线通过接地卡连接。
At both ends of conduit in non-explosion proof area, the bridging lines should welded or the earth wires should be connected with clamp.
非防爆区域内穿线管连接处两端，应焊接跨接线，或用接地线通过接地卡连接。
At both ends of conduit in non-explosion proof area, the bridging lines should welded or the earth wires should be connected with clamp.
应用推荐