压缩空气注入在左端进气歧管管。
Compressed air is injected at the left end of the intake manifold tube.
进气歧管把发动机进气道口连接起来。
The intake manifold connects the carburetor to the intake ports of the engine.
注塑成型工艺是开发塑料进气歧管的重要环节。
The injection molding is an important tache to exploit plastic air intake manifold.
内燃机(1)通过进气歧管(7)供应燃烧空气。
An internal combustion engine (1) is supplied with combustion air via an inlet manifold (7).
从事汽车进气歧管、气缸罩盖设计经验五年以上;
At least 5 years experience on intake manifold and cylinder cover; 4.
首先对发动机及其进气歧管的结构功能进行了分析。
First, the structure and function of the engine air intake manifold are analyzed.
目前,国内设计制造塑料进气歧管的技术还不过关。
针对国内目前还不能自主设计塑料进气歧管注塑模具。
Aim to be not able to design mould of plastic air manifold by domestic technique.
下面的图片中显示的时间轴,齿轮和时间的进气歧管。
The picture below shows the timing shaft, timing gear and the intake manifold.
一种部件,例如进气歧管或节气门本体,具有空气通道。
A component, such as an intake manifold or a throttle body, has an air passage.
使设计开发的柴油机塑料进气歧管在装配性上是良好的。
The assembly property of plastic air intake manifold is researched.
活塞主要因进气歧管真空度的变化而在活塞腔内上下移动。
The piston moves up and down in the piston chamber primarily in response to changes in intake manifold vacuum.
风门表面留有安装摩托车进气管和发动机进气歧管的位置。
The Throttle body provides surfaces for mounting between the Motorcycle's air intake duct and the engine intake manifold.
空气滤清器通常位于空气流到你的节流阀总成和进气歧管。
The air filter is usually located in the air stream to your throttle valve assembly and intake manifold.
总结出了在设计塑料进气歧管注塑模具时要注意的几个问题。
Summarized some important experience on designing injection mould of plastic air intake manifold.
如果发动机回火,进气歧管骤增的压力就迫使阀门向后移动。
If the engine backfires, the sudden pressure in the intake manifold forces the valve back.
这是因为当发动机熄火时,进气歧管冷却而产生轻微的真空。
When the engine is shut off, the intake manifold cools and a slight vacuum forms as a result .
这种装置称为“歧管热控制阀”,它拼装在排气与进气歧管中。
This device, called the manifold heat-control valve, is built into the exhaust and intake manifold.
安装汽缸盖,进气歧管和排气管,请参阅本部分的汽缸盖安装。
Install cylinder head, intake manifold, and exhaust manifold, refer to cylinder head installation in this section.
不用说,缺乏表现与四国,我开始让客户化定制的进气歧管等。
Needless to say the performance was lacking so with the G4 I began making custom built intake manifolds.
介绍了发动机进气歧管压力传感器的标定系统和传感器静、动态标定方法。
This paper introduces the calibration system and static and dynamic calibration method of an engine intake manifold pressure sensor.
尼克拿过来一根螺栓套杆,把一头儿贴在进气歧管上,然后凑过去听了听另外一头儿。
Nick set one end of a long socket extension on the intake manifold and listened to the other end.
随着拖动转速升高,进气歧管压力降低,对应的喷油策略也应随之调整;
The intake manifold pressure is lower when the cranking speed increases, thus the fuel metering strategy should be modified.
本文主要进行可变式进气歧管的三维曲面重建和空气流动模拟分析的研究。
This thesis mainly carries on research of three dimensional surface reconstruction of variable intake manifold and air fluid simulation analysis.
节气门体总成安装在歧管口,进气歧管接口尺寸如节气门体总成轮廓图所示。
The Throttle body assembly will mount to the manifold snout and intake manifold interface dimensions are defined on the Throttle body assembly outline drawing.
由于重新设计的阀门,发动机不敏感,空气压力,将很容易运行只需吹的进气歧管。
With the redesigned valves, the engine is not sensitive to air pressure and will easily run just by blowing into the intake manifold.
燃料系只有这样几个主要部件,如燃油箱、输油泵、燃油滤清器、化油器、进气歧管等。
The fuel system only has several major parts such as fuel tank, fuel pump, fuel filter, carburetor, intake manifold, etc.
第二部分用STAR - CD流体软件对可变式进气歧管进行空气流动数值模拟分析。
The second part carries on the air fluid simulation analysis of variable intake manifold with the STAR-CD fluid software.
发动机配件类:齿轮室、气门室罩盖、链轮室罩盖、预热器座、水泵泵盖、进气歧管、泵箱;
Engine fittings series:Gear chamber, Cavaera cover, Sprocket rooms cover, Preheaterbase, Water pump Cover, Intake manifold, Pump box.
进气系统主要包括空气滤清器、进气道、化油器和进气歧管。一些发动机在进气系统中有增压器。
The intake system mainly includes the air filter, intake ducting, the carburetor, and the intake manifold. Some engines have supercharger in the in take system.
应用推荐