仿真试验表明，两种模型的动态过程均符合对象的机理，同时，对实时模快的有效性进行了探讨。
The experimental results show that the dynamic process of two type model accords with the mechanism of the object, at the same time, the validity of real time capable module is discussed.
方法采用拓能系统的固定装置、计划系统、激光灯、弓形尺、头部模型（简称头模）模拟3DCRT的实施过程进行质量控制分组实验。
Methods To do quality control experiments to simulate the process of 3D-CRT by means of Topsland system, radiation treatment -planning system, laser light, bow form ruler, head model.
采用有限元多晶体模型对无模多点成形条件下不同加载方式的板条多点弯曲成形过程进行了数值模拟。
Numerical simulation of multi point bending process of strip under different loading paths is dealt with the finite element polycrystal model.
消失模铸造干砂充填紧实过程中，干砂对模型壁的动态压力可间接反映此处干砂的紧实程度。
The dynamic pressure on pattern wall can reflect indirectly the compaction degree of sand during the course of filling and compaction of sand on EPC.
本文介绍了燃烧实验室所进行的媒水混合物流化床燃烧过程数学模化工作第一阶段的研究结果——初定模型的基本情况。
The result of the first stage work of mathematically modelling for fluidized bed combustion process of coal water mixture the primary model is reported in this paper.
结果：制模过程中，因窒息死亡4只，痉挛型脑瘫模型组3只，对照组1只。
RESULTS: During the model establishment, there were 4 deaths including 3 in model group and 1 in control group.
利用产生最有效锁模的腔参数及涨落模型，进行了激光过程的数值模拟。
Taking the cavity parameters providing a most efficient mode locking and based on fluctuation model, we performed a numerical simulation of laser operation.
其次介绍了注塑模流动模拟理论，建立了流动过程的数学模型。
Second, flow simulation theory of injection plastic mould is introduced, math model of flow is established.
用自适应过程减小参数不确定性的影响，并通过动态滑模控制器的高鲁棒性抑制机器人模型中的未知非线性动力学及测量噪声等的影响。
The adaptive process extenuates the influence of parameter uncertainty, and the robustness of the dynamic sliding mode control inhibits the influence of unknown dynamics and measurement noise.
建立了描述厚层光刻胶内衍射光场形成过程的物理模型，并利用傅里叶模方法模拟计算和分析了其内部衍射光场分布。
Then Fourier model method, mostly applied to study the diffractive properties of gratings is adopted to analyze the diffractive image field in thick film photo resist.
推导出了双转子机构抛光模在露边时的去除函数修正模型，为解决加工过程中的边缘效应问题提供了理论基础。
The amendment model of the removal function is set up. Theoretical basis is given for solving the edge effect problem.
首先建立了汽车保险杠树脂传递模塑充模过程的三维数学模型；
A three-dimensional mathematical model of the resin transfer molding(RTM) filling process for the automobile bumper was presented.
首先建立了汽车保险杠树脂传递模塑充模过程的三维数学模型；
A three-dimensional mathematical model of the resin transfer molding(RTM) filling process for the automobile bumper was presented.
应用推荐