根据飞行仿真模块的输出，通过坐标变换、比例限制、信号洗出和滤波等，形成运动平台的驱动信号。
On the basis of output of flight imitate system, the driving signal of flight simulation is formed by coordinates transforming, scale limiting, signal washout and filter.
同时还详细描述了前置音频放大器，三角波产生电路、比较器，死区控制电路，输出驱动电路等子模块的设计内容。
And then describe the module of pre audio amplifier, triangle generator, comparator, death time control and output driver etc.
再开发一个测试驱动模块，控制测试数据输入和测试结果输出。
Then, generate a testing drive module to control input testing data and output testing results.
开关量输出模块是将PLC内部低电压信号转换成驱动外部输出设备的开关信号，并实现PLC内外信号的电气隔离。
Output switch module is a low voltage PLC internal drive external signals into the switching signal output device and to achieve internal and external PLC electrical signal isolation.
基本驱动模块电路输出波形的测试结果表明，这种设计方法是完全可行的。
The output waveform of the module is the same figure as the simulation waveform. This result indicates that the design method is feasible.
如果实际输出设备的电流较大，输出模块无法直接驱动，可增加中间放大环节。
If the actual output current of the larger equipment, the output module can not be directly driven, to increase links to enlarge the middle.
在硬件设计主要介绍系统组成中的外部存储器模块与视频输入输出模块，介绍了使用片上支持库编写DM642中视频驱动程序的方法，以及编写过程中DM642中断和直接存储器存取（DMA）的应用；
The hardware chapter introduces the external memory module and video I/O module, programs video-driver for the DM642 by using CSL, discuss the applications of interrupt and direct memory access (DMA).
该驱动板以现场可编程逻辑门阵列为DSP与编码器、脉冲命令和功率模块等电路之间的接口，以最新的智能功率模块(IPM)作为功率输出驱动芯片。
FPGA is used as interface between the DSP and the encoder, pulse command and power module. The latest intelligent power module (IPM) is used to provide the function of power stage.
热敏绘图仪驱动模块由状态诊断、表头输出、曲线输出三部分组成。
Driver for thermal plotter consists of state checking, head table output and curve output.
所有元器件均来自一个品牌，包括真空断路器，空气断路器，电流接触器，热继电器，驱动，可编程控制器，输入输出模块，电站管理系统继电器和仪表，不间断电源，传感器和照明器材。
All of components come from one brand, from vacuum circuit breakers, air circuit breakers, contactors, thermal relays, drives, PLC, I/O, PMS relays and meters, UPS, sensors and lighting fixtures.
控制板包括信号采集模块、控制器和输出模块，控制器与高压水泵的驱动电机相连接。
The panel comprises a signal collect module, a controller and an output module, wherein the controller is electrical connected to a driver of the high pressure pump.
控制器硬件包括通信模块、驱动模块、输入输出模块等，是在嵌入式系统基础上完成的。
Last, the control software which includes driver program and application program are developed based on embedded operation system Linux.
控制器硬件包括通信模块、驱动模块、输入输出模块等，是在嵌入式系统基础上完成的。
Last, the control software which includes driver program and application program are developed based on embedded operation system Linux.
应用推荐