推导出应力控制时的线性动态系统(恒压输出控制系统)的相关传递函数和伯德图。
In succession deduct correlative transfer function and bode diagram of stress control's linear dynamical system (constant pressure output control system).
据此研究之结果将作为日后以数值法引用EDA理论应用于多输入多输出控制系统之设计。
The design about a MIMO servo mechanism by using numerical EDA method will base on the result of this study.
第二部分着重讨论了激光数码冲印输出控制系统的解决方案，以及方案中各部分关键器件的原理和应用。
We focused on the solution of the output control system and the applications of the key devices in the system in the second part.
外围输出控制系统由发光二极管、继电器、数字开关等模拟外围设备，控制其它的弱电设备和一般的强电设备。
The periphery output control system is composed of analog peripheral device such as LED, relay, digital switch etc, to control the other weak-current devices and general heavy-current devices.
通常应避免在版本控制系统中存放构建输出品。
PB 150钢制结构制造于苏格兰，其动力输出装置及控制系统制造并检测于OPT位于美国新泽西州沃里克市和边宁顿市的工厂中。
The PB150's steel structure was fabricated in Scotland, and the power take-off and control system was built and tested at OPT's facilities in Warwick and Pennington in New Jersey, US.
讨论了网络控制系统在输出反馈情况下随机最优控制器的设计；
The design of stochastic optimal controllers of networked control systems with output feedback is also presented.
电子控制系统基本上由计算机或电子控制组件、发动机显示线束、输入的传感器和输出的执行器组成。
The electronic control system consists basically of the computer or electronic control module, engine wiring harness, input sensors, and output actuators.
低频电磁场电流测控系统包括电流测试和输出控制两个部分，由软件和硬件相互配合组成一个完整的计算机控制系统。
The current measurement and control system in a Low-frequency Magnetic Field is a comprehensive system of hardware and software, including two parts: current measurement and computer control.
基于CPU 224的输入输出点数有一定的局限性，此控制系统将显示灯部分只表示出了一组红绿灯指示工作与停止。
CPU 224 based on input and output points have certain limitations, the control system will show some light to show only a set of traffic lights work and stop instructions.
控制系统的功能是在负载随时变化的工况下，确保机组转速恒定，并使电压输出控制在要求范围之内。
The control system functions to keep speed of the machines substantially constant and the voltage within prescribed limits, even the load may change.
控制系统直接输出加工文件方便快捷。
Control system direct output processing files quick and easy.
并证明了该最优输出反馈控制律可使网络控制系统均方指数稳定。
The paper proves that optimal controllers can stabilize the exponentially mean square of networked control systems.
本文讨论了一种仿人智能控制方法，并将其具体应用于二输入、二输出的液位控制系统。
The paper discusses an artificial intelligent control means which is particularly used in the liquid level control system with double input and double output.
本文对于包含多输入多输出控制器的鲁棒控制系统作了系统化的研究。
A systematic procedure has been developed for the synthesis of robust regulatory control systems comprising multi-input multi-output controllers.
这些条件也可用来解决实际控制系统的动态输入输出解耦问题。
These conditions can be used to solve the decoupling problem of dynamic input and output of an actual control system.
描述了两个控制系统间的输出反馈相似的概念。
The output feedback similarity between two control systems is described.
设计一种以串行输入为基础，串并混合方式输出的多路控制系统。
A multiplex control system based on serial entry and output in series-parallel mixed mode is designed.
高精度的电容式位移传感器用来测量动平台的实际输出并形成反馈控制系统。
High precision capacitance displacement sensor is used to measure the actual output of moving platform and formed a system of feedback control.
在此基础上，讨论多采样率数字控制系统在输出反馈下的极点配置问题。
Then the pole assignment of multirate digital control systems under output feedback is discussed.
根据输入、输出的要求对控制系统的硬件进行设计，包括数据采集、人机通道的设计。
According to input, the output request has carried on the design to the control system hardware, including data acquisition, man-machine channel design.
提出确定多输入多输出网络控制系统的最大允许时延界的新方法。
A new method is proposed to obtain the maximum allowable delay bound (MADB) of multi-input and multi - output (MIMO) networked control systems.
视频信号传输，输出，接收装置和复制控制系统。
Video signal transmission device, video signal output device, video signal reception device, video signal duplication control system.
针对多输入多输出非线性锅炉-汽机系统在大范围运行工况下参数发生变化的情况，设计了基于渐近跟踪控制的T - S模糊控制系统。
T-S fuzzy control system based on asymptotic tracking control is designed for a MIMO nonlinear boiler-turbine system whose parameters vary under the operating condition within wide range.
以步进电机作为控制系统的执行机构，讨论了无模型控制器的输出与步进电机之间的软件连接问题。
The software connection problem between the output of non-model controller and step motor, is discussed using step motor as the actuator of control system.
针对单输入单输出和多输入多输出网络控制系统中存在的时延抖动和时延偏移问题，提出了在控制器和执行器前设置缓冲区的方法。
For the problems of delay jitter and delay skew consisting in SISO and MIMO networked control systems, the method of setting buffers before controller and action is bring forward.
研究了具有不确定时延的动态输出反馈网络控制系统鲁棒控制器设计问题。
The problem of robust controller design for dynamic output feedback networked control systems with uncertain time-delay is studied.
介绍了奥迪a6型轿车发动机的传感器和输出装置在车上的位置，及其控制系统的故障代码表等。
The paper introduces the locations of sensors and output mechanisms for Audi A6 car engine in the vehicle, and introduces also its fault code table, etc.
介绍了奥迪a6型轿车发动机的传感器和输出装置在车上的位置，及其控制系统的故障代码表等。
The paper introduces the locations of sensors and output mechanisms for Audi A6 car engine in the vehicle, and introduces also its fault code table, etc.
应用推荐