电子控制系统基本上由计算机或电子控制组件、发动机显示线束、输入的传感器和输出的执行器组成。
The electronic control system consists basically of the computer or electronic control module, engine wiring harness, input sensors, and output actuators.
本文讨论了一种仿人智能控制方法，并将其具体应用于二输入、二输出的液位控制系统。
The paper discusses an artificial intelligent control means which is particularly used in the liquid level control system with double input and double output.
本文对于包含多输入多输出控制器的鲁棒控制系统作了系统化的研究。
A systematic procedure has been developed for the synthesis of robust regulatory control systems comprising multi-input multi-output controllers.
针对多输入多输出非线性锅炉-汽机系统在大范围运行工况下参数发生变化的情况，设计了基于渐近跟踪控制的T - S模糊控制系统。
T-S fuzzy control system based on asymptotic tracking control is designed for a MIMO nonlinear boiler-turbine system whose parameters vary under the operating condition within wide range.
基于CPU 224的输入输出点数有一定的局限性，此控制系统将显示灯部分只表示出了一组红绿灯指示工作与停止。
CPU 224 based on input and output points have certain limitations, the control system will show some light to show only a set of traffic lights work and stop instructions.
这些条件也可用来解决实际控制系统的动态输入输出解耦问题。
These conditions can be used to solve the decoupling problem of dynamic input and output of an actual control system.
设计一种以串行输入为基础，串并混合方式输出的多路控制系统。
A multiplex control system based on serial entry and output in series-parallel mixed mode is designed.
根据输入、输出的要求对控制系统的硬件进行设计，包括数据采集、人机通道的设计。
According to input, the output request has carried on the design to the control system hardware, including data acquisition, man-machine channel design.
通过解耦，三轴转台系统成为三个单输入，单输出线性系统，为理论分析设计控制系统提供了转台模型。
The model is transformed into three single input and single output linear systems, and then it can be analyzed and designed by the linear system theory.
从系统论的观点看，项目人力资源管理是一个多输入—多输出反馈控制系统。
From the viewpoint of system theory, project human resource management is a feedback control system with multi-inputs and multi-outputs.
本文介绍了几种典型的汽车自动变速器锁止离合器电子控制系统，并分析了其输入、输出和控制策略。
This paper introduces some typical electronic control systems for vehicle automatic transmission's lock-up clutch, and analyses the input, output and controlling tactics of the systems.
在研究自动控制系统之前建立一个数学模型是为了更简捷地描述输出变量与输入变量之间的关系。
A mathematic modeling was built before study automatic control system to briefly describe the relation between input and output variables.
针对单输入单输出和多输入多输出网络控制系统中存在的时延抖动和时延偏移问题，提出了在控制器和执行器前设置缓冲区的方法。
For the problems of delay jitter and delay skew consisting in SISO and MIMO networked control systems, the method of setting buffers before controller and action is bring forward.
提出了带有周期通信序列（PCS）的多输入与多输出分布式网络化控制系统的故障诊断方法。
The fault diagnosis of multi-input and multi-output distributed networked control system with periodic communication sequence(PCS)was investigated.
本文将预测过程模拟成一个“模糊控制系统”，以预测因子作为系统的输入，预测量作为系统的输出。
This paper simulates the forecast process as a"fuzzy control system", takes the forecast factors as the input data , and the forecast quantities as the output data.
控制系统包括电控柜、控制台，显示器和电脑。控制系统具有良好的人机界面、数据输入输出功能、图形显示系统。
Including power panel, control desk, monitor display and PC computer, the PLC control system has friend interface, data input and output, diagram display.
采用广义输入输出包含原理将多余度控制系统表示为多重包含系统，使之易于分析与设计。
A generalized input and output inclusion principle is used to express the multiple redundant control systems so that the analysis and design procedure are simplified.
气体计量调度自动控制系统设计采用ADAM- 5000系列，主要由CPU控制器、输入模件、输出模件等组成。
The automatic control system for gas metering and dispatching adopts ADAM-5000 series, which are composed of CPU controller, input mold piece, output mold piece etc.
在认真分析了巡航控制系统的基本原理，确定了输入输出信号以后，提出了一种闭环控制的巡航控制系统设计方案。
After analyzing the basic principle of CCS and defining input signals and output signals, a kind of close-looped control scheme is brought forward.
主要论述了在PLC控制系统中，为了提高系统的安全可靠性，PLC的输入输出接口应注意的事项和较实用的接线方式。
The paper mainly discussed the practical connection modes in the PLC the points of attention for PLC control system, so as to improve input and output interface and the system safety and reliability.
提出确定多输入多输出网络控制系统的最大允许时延界的新方法。
A new method is proposed to obtain the maximum allowable delay bound (MADB) of multi-input and multi - output (MIMO) networked control systems.
同时本方法以单输入单输出形式，使控制系统的实施非常简单。
Using SISO form makes the control system very simple to implement.
本文经过重新定义增广误差信号，给出了有延时情况下线性时不变离散时间单输入单输出被控对象的模型参考自适应控制系统的超稳定性设计方法。
This paper presents a hyperstable scheme for designing discrete model reference adaptive control system for lineartime-invariant SISO plant, based on a redefined augmented error signal.
本文提出了一种应用模型参考自适应原理的变参数PID调节器，适用于单输入——单输出的一阶、二阶控制系统。
This paper proposes a PID regulator of changeable parameters applying model reference adaptive principle. It is suitable for one-order, two-order control systems of single input and single output.
给出了单输入单输出和多输入多输出网络控制系统中存在数据包丢失情况下均方随机稳定的充分条件和丢包边界的确定方法。
The sufficient stability conditions of SISO and MIMO networked control system with data dropouts are presented, data dropout rate is determined to ensure stability of NCS.
复杂控制系统一般存在多个输入、输出变量，控制整定参数数量也较多，所以采用常规的整定方法非常困难和烦琐。
Generally there are a lot of variables of input and output in complex control systems, and there are many control parameters in the systems as well.
最后，本文讨论了控制系统中用到的开关量的输入和输出电路的设计，并给出了具体的应用电路。
Finally, the cue of the design for switching value input and output interface circuits was given, and then a circuit in accordance with the thought of the design produced.
第三条线路连接到PLC输入卡或控制系统上的输出端。
The third wire is the output which is connected to the PLC input card or the control system.
第三条线路连接到PLC输入卡或控制系统上的输出端。
The third wire is the output which is connected to the PLC input card or the control system.
应用推荐