在切纸机工作过程中，纸辊的拉纸速度和刀辊的旋转速度共同决定了切下纸张的长度。
During the working of paper cutting machine, both the speed of drawing paper and the revolving speed of cutter decide the length of paper.
试验结果表明梳理机上工作辊与锡林速比、针梳道数、喂入根数和牵伸倍数对涤纶条中的纤维长度、毛粒含量有组合影响。
The experimental showed that fibers length and neps were influenced by speed ratio between cylinder and worker, gilling number as well as combination of sliver feed weight and gilling draft.
通过打印机绘图仪输出了磁条的磁场（B）与长度（L ）的曲线、磁辊的磁场（ B） 与角度（DEG） 的曲线。
Then the curves of magnetic strips field ( B) with length ( L ) and magnetic roller field( B) with its angle (DEG) are described by printer.
烘箱总长度10米，内部导辊为拱型排列，烘箱侧面安装走道及防护栏。
The total length of the oven is 10 m. Inside oven, bearing rollers are shaped in arch. There are walkway and guardrail at the side of the oven.
在滚锻时，圆的或是扁平的棒料放在模辊之间缩小横截面增加长度制成诸如轮轴、板簧之类的零件。
Roll forgings. In roll forging, a bar stock, round or flat is placed between die rollers which reduces the cross-section and increases the length to form parts such as axles, leaf springs etc.
论述了采用双阶梯支承辊的必要性。提出了接触长度、阶梯深度及工作辊凸度的计算方法。
The paper discusses the necessity of applying double stepped backup rolls, and describes the methods for calculating the contact length and stepped depth and work roll crown.
当磨辊与磨环达到一定磨损后，调整高压弹簧长度，保持磨辊于磨环之间的恒定碾压力。
When the roller mill with a certain ring wear, the length of spring pressure adjusted to maintain a constant link between roller mill on the pressure roller.
这种长度测量系统利用四辊轧机液压微调计算机厚度控制系统的压力检测信号，作为咬钢和抛钢识别信号。
The system takes the pressure signal of hydraulic micro-adjust of the four rollers mill for signal of steel plate entering into rolling mill and signal of steel plate out of rolling mill.
根据这些参数加工螺纹钢筋成品辊孔槽，从而解决了螺纹钢筋长度不足的问题。
Based on the data, the finishing roll slot has been designed and produced. In this way, the reinforcing steel tooth length problem of the shortcoming can be solved.
轴承套圈余热退火辊底炉生产线是一高度机械化自动化的特大型加热设备。由于受厂房长度限制，设计成长方形的闭环结构，这是本设计的特点之一。
The large roller hearth furnace production line for annealing hot bearing RACES is designed as a rectangular and closed structure under the limit of the length of available shop.
本文重点讨论轧辊弹性压扁沿辊身长度分布的规律及最佳弯辊力，有一定参考价值。
In this article author puts emphasis upon the discussion about distribution regularity of roll flattening along the length of roll body and optimum roll-bending force, which is of certain value.
加载压力被单独为各自的骑辊加压，根据压区压力要求和各自的复卷长度，相关的纸卷直径，根据在TRUTEC设定的曲线。
The loading pressure is calculated separately for each rider roll depending on the required nip pressure and respective sheet length. The related diameter–dependent set curve is stored in TRUTEC .
以某中板厂生产条件和数据为基础，讨论了变接触长度支承辊辊间接触压力相等时的轧辊变形情况。
Based on production conditions and data, this article discusses the varying contact length back-up roll deformation under the condition of equal contact pressure between rolls.
可以任意转换齿轮版辊，改变印刷长度。
The plate cylinder can be changed at whim and change the length of printing.
可以任意转换齿轮版辊，改变印刷长度。
The plate cylinder can be changed at whim and change the length of printing.
应用推荐