提出了斜轧扩管机轧辊辊型设计方法。
In addition, method for roll groove design of the mill is put forward.
根据钢管冷斜轧过程的变形特点,建立了辊型设计系统。
Based on the deformed characteristics of the process of steel tube cold cross rolling, an system of roll configuration design has been established.
结合已设计出的45~76焊管生产线中的六辊矫直机,阐明了矫直辊辊型设计的一种方法。
The paper, combined with the 45~76 straightening machine designed, provides a theoretical method for designing the straightening roll camber.
该模型在连轧机参数优化设计和辊型配置优化设计系统中均得到应用,效果良好。
The model was used in the rolling parameters optimal design system and the rolling shape optimal design system, and good results were obtained.
本文所依托的课题的模型及软件现已成功应用于中国第二重型机械集团公司对于弯辊液压系统的设计分析之中。
The model and the software depending on the applied subject were applied to design and analyze of hydraulic bending roller control system in China National Erzhong Group Co.
各种设计包括单壳,双壳,坚固型,带涂层和电热辊。
These designs include single shell, double shell, solid, coated and electrically heated rolls.
介绍了螺旋焊管成型器内压辊斜置小辊线接触辊型的设计方法(经验公式设计法)。
The article introduces the design methods of contact roller of internal press roller of forming machine of SSAW pipe mill(experience formula design).
本文提出的型槽系设计方法及展宽系数公式,对于类似产品辊锻工艺设计有普遍指导意义。
The design method of groove system and wide extension coefficient formula proposed in the paper are very significant for roll forging design of other similar products.
经现场实践应用表明,采用该方法设计出的工作辊、支持辊辊型曲线适应性好,并大大地改善了板凸度和轧辊磨损情况。
The application results show that work roll and backup roll designed with this method have good adaptability, and the plate crown and roll consumption have been reduced greatly.
将该软件系统用于设计FRW2000型辊道窑获得了满意的设计结论。
Some satisfactory results using this system to design FRW2000 roller kiln are stated in this paper.
该经济型JJM手动纵切复卷机主要设计用于各种成本效益高的纸转换工艺,包括POS机辊,卷柜和工程机辊等。
The economical JJM Manual Slitter Rewinder is primarily designed for a variety of cost-efficient paper converting processes, including POS rolls, counter and engineering rolls, and others.
根据CVC轧机的工作原理及板带轧制基本要求,探讨了CVC轧机工作辊辊型的选择条件,井导出了立方抛物线辊型的设计或磨辊曲线公式。
According to the principle of CVC mills, the selection of work roll shape is discussed. Formulas used for the design of CVC work roll shape are given.
介绍了自行开发设计的一条连续型煤生产线的工艺过程和主要生产设备,重点介绍了对辊式型煤成型机的工作原理及结构特点。
This paper introduced the development of briquette production line, including the technical process and the main equipment. The roll type briquetting machine was introduced in details.
在实验的基础上,用工程近似法推导出在四辊组合孔型轧制圆系统产品时的力能参数,建立了轧制圆型系统产品的计算机辅助孔型及优化设计。
On the base of experiments, the author deduced some power energy parameters of round bar in four roll pass system, established the computer aided roll pass design.
同时为使设计出的辊型更趋完善,在计算过程中还引入了压力、板宽加权系数。
At the same time, the weight coefficients of plate width and rolling force have been used in the calculation of roll shape in order to improve the calculation accuracy.
本文阐述了三辊Y型轧机连轨的基本特点及其孔型设计计算方法。
The fundamental characteristics of Y-type rolling mill with three rollers and methods. of designing and calculating the grooves are described in this paper.
通过对提供的典型规格产品进行辊型优化设计计算,确定每一架轧机工作辊和支承辊的辊型参数。
Roll shape parameters of every working rolls and backup rolls were specified through the optimization design calculation of the typical productions.
生产实际应用表明,新设计的辊型不仅明显降低了板凸度,同时使轧辊磨损均匀,辊耗量大大下降。
The practical application indicates that the new design not only reduces the convexity of the roll profile obviously, but also leads to homogeneous attrition of rolls and low rol...
初步建立了大型辊坯椭圆型槽的设计方法,可供大型辊坯辊锻设计时参考。
A method for designing the elliptical cavities of the large roll forging has been developed. The...
初步建立了大型辊坯椭圆型槽的设计方法,可供大型辊坯辊锻设计时参考。
A method for designing the elliptical cavities of the large roll forging has been developed. The...
应用推荐