进而，得到数据包载荷长度在给定的区间上服从一定的分布条件下，RTS门限和终端发送一个数据包所需消耗能量的平均值之间的关系。
The relation of RTS threshold and average energy consumption per frame is produced in the assumption that the frame payload's length is distributed in a given interval.
考虑脱层壳的三种不同屈曲模态，分析了边界条件、脱层长度、深度对脱层壳屈曲载荷的影响；
Three difference buckling modes of delaminated shell were considered. The influence of boundary condition, length and depth of delamination on buckling load was analyzed.
这些非线性效应，可在测定所有裂纹长度的柔度方法时，采用最大载荷不变的方法予以消除。
The effect of these nonlinearities can be avoided by determining compliance at the same maximum load for all crack lengths investigated.
在此状态下可在任意长度的压杆上，加任意大小的轴向载荷，而不产生弯曲。
With this situation, any amount of axial load can be applied to compressive bar of arbitrary length without bending.
该应力可通过增加桥接长度减小，因载荷分布于钢板更长区域。
Such stress is reduced by increasing the bridging length, since the forces are distributed over a larger area of the plate.
在试验温度区内，控制韧性的因素是断裂载荷、纤维裂纹长度和单位纤维裂纹扩展能量。
Within the range of test temperature, the factors controlling the toughness are fracture loads, the lengths of fibrous crack, and the energy absorbed by each fibrous crack extension.
在平衡裂纹条件下，将塑性部分表达为该载荷与裂纹长度的函数。
Under the condition of equilibrium crack the plastic component of the displacement can be regarded as a function of load and crack length.
最后分析在恒幅疲劳载荷作用下，不同的最大凹陷深度和凹陷影响区域的长度对楔形凹陷立管的疲劳寿命的影响。
Finally, the effect of different maximum depth and length of the dent on the fatigue life of dented riser under the constant amplitude fatigue loads was studied.
着重讨论了集中力的倾角对弯曲形状、载荷—挠度关系及塑性区长度的影响。
The emphasis of the analysis is put on the effects of the angle of inclination of the concentrated force upon the deformed shape, the load-deflection relationship and the length of the plastic region.
水平井的前端套管一般是承受压应力的，随着进入水平段的套管长度的增加，大钩载荷反而下降；
In horizontal well, frontal side casing string is usual bearing pressure. In horizontal hole section, with the length of casing increase, the hook load is decreasing on the contrary.
载荷越大，焊缝与母材的强度差别越大；积分路径中包含的焊缝与母材界面长度越大，J积分的差值越大。
Moreover, the difference of J-integral values increases with the increasing of the load and strength mismatching difference and the path-enclosed length of interface between weld metal and base metal.
研究表明，水平井眼中钻柱所能承受的临界载荷和所使用钻杆的单根长度有密切关系。
The research indicated that the critical compressive force of drill stem in horizontal well is closely related with the length of single drill pipe in use.
在满足AUV的设计性能要求的同时，实现了使得AUV总重量和推进功率最小，有效载荷段的长度最大等目标函数。
While the requests of AUV design performance are met, the objectives of minimizing gross weight and maximizing propeller power and payload length are achieved.
分析了不同径厚比、边界条件及脱层长度、深度、位置对脱层壳屈曲载荷的影响。
The influence of different ratios of radius to thickness, boundary condition and length, depth and po…
当外加载荷大小、加载宽度及结构体长度相同时，柱壳结构中截面上拉应力最大值大于平板。
When their loading sizes, widths and lengths are the same, the maximum value of stress at the center of cross-section will be greater than that of the plane structure.
钻杆的单根长度越长，钻柱所能承受的临界载荷越小。
The longer the single drill pipe, the lesser the critical compressive force of drill stem.
ATM适应层（AAL）的作用就是从不同的来源或者应用接收数据并转换或改写成能放入一个ATM信元的有效载荷的长度为48字节的段。
The purpose of the ATM adaptation layer (AAL) is to receive the data from the various sources or applications and convert or adapt it to 48-byte segments that will fit into the payload of an ATM cell.
结合实验载荷-位移曲线，绘出载荷-裂纹扩展长度曲线，用于静态断裂实验中确定裂纹的起裂载荷。
Based on loading-displacement curve, loading-length of crack expanding is drawn out which can determine crack initiation loading of static fracture experiments.
结合实验载荷-位移曲线，绘出载荷-裂纹扩展长度曲线，用于静态断裂实验中确定裂纹的起裂载荷。
Based on loading-displacement curve, loading-length of crack expanding is drawn out which can determine crack initiation loading of static fracture experiments.
应用推荐