通过一个广义的傅里叶级数方法求解的控制方程，并随后得到相应的载荷挠度曲线。
The governing equations are solved by means of a generalized Fourier series method, and subsequently the corresponding load deflection curves are obtained.
对各向同性、均布载荷及简支点等间距分布的简化情况计算了圆板的最大挠度。
The maximum deflection is calculated in case of isotropic, uniformly loaded circular plate and equidistant bearing points.
测试涂挂不同涂料的模样在变载荷下的挠度值。
The deformations (deflection value) of the patterns with different coatings were measured under different loads.
对正交异性扁薄圆柱壳在均布载荷及集中载荷作用下的大挠度问题进行了理论计算和测量。
Orthotropic shallow cylindrical shells with large deflection are theoretically calculated and experimentally analyzed under the cations of uniform and concentrated loads.
高径比（H/D）较大的塔在风载荷的作用下，在塔顶处会引起一定的静挠度。
There appears some flexibility at the top of tower with high ratio of height to diameter (H/D), caused by wind load.
采用拖带座标系和逐步增量法。还讨论了大挠度对载荷的影响。
Comoving coordinate system and incremental process are adopted and the effect of large deflection on loads is also discussed.
随着最大载荷保持时间的增加，塑木复合材料进入延迟弹性变形阶段越晚，弯曲挠度增加越快，断裂寿命降低。
The delayed elastic deformation stage came later, the bend deflection increased more quickly, and breaking life shortened with the increase of the prolongation of the maximum load hold time.
本文应用幂级数方法求出了在均布载荷作用下夹层圆板大挠度问题的精确解。
This paper gives the exact solution of large deflection of circular sandwich plate under the action of uniform lateral load by the method of power series.
还表明，在一定温度下，载荷-挠度曲线越陡，合金的抗弯强度一般也越高。
It was also found that at a fixed temperature the transverse-rupture strength of the alloy generally increased with the steepness of load-deflection curves.
给出了脱层屈曲临界载荷、挠度曲线与脱层半径、搭桥因子等的封闭关系式。
The closed form solutions of the critical load and the deflection contour of the delamination buckling decided by delamination radius, and the bridging factor are obtained.
本文将对等壁厚、等经受变载荷塔内弯矩和挠度进行探讨。
In this paper, the calculation of the moments and deflections for the columns with uniform diameter and thickness but subjected to variable loads was discussed.
给出了小挠度下，在外界载荷作用下总应力表达式和薄膜机械灵敏度表达式，并分析了残余应力对二者的影响。
We present an analytical solution for the total stress and mechanical sensitivity of highly boron doped si diaphragm with small deflection considering effect to result from the residual stress.
本又讨论了映象法，并利用映象法求解了板在集中载荷作用下的挠度。
This paper discussing the mirror photo method and finding the solution deflexion of the plates through mirrir photo method under the concentrate force.
着重讨论了集中力的倾角对弯曲形状、载荷—挠度关系及塑性区长度的影响。
The emphasis of the analysis is put on the effects of the angle of inclination of the concentrated force upon the deformed shape, the load-deflection relationship and the length of the plastic region.
本文给出了正交各向异性变厚度周边简支圆薄板在均布载荷下大挠度问题的解。
The solution of large deflection problem of thin orthotropic circular plates with variable thickness under uniform pressure under simply supported boundary condition is obtained in this paper.
本文给出了正交各向异性变厚度圆薄板在均布载荷与集中载荷作用下大挠度问题的解。
The solutions of a large deflection problem of thin orthotropic circular plates with variable thickness under uniform pressure and under concentrated load are obtained in this paper.
采用薄板弯曲理论研究了均匀载荷作用下多晶金刚石方膜在小挠度和大挠度下的应变分布情况。
The strain distribution based on small and large deflection theories of diamond square diaphragm was studied using theories of plate bend.
本文通过钢筋混凝土芯梁及粘贴钢板补强混凝土复合梁的疲劳试验，研究了它们在疲劳试验过程中载荷和加载线位移及跨中挠度的变化规律。
This paper deals with the load-deflection and load displacement curves of beams basedon the fatigue experiments of plated and unplated RC beams.
对带有初始挠度加劲薄板的临界载荷、极限载荷、波形的重新分布有了一定的感性认识。
Certain perceptual knowledge to critical load, limit load, waveforms redistributing, which all belong to the stiffened panel with initial defects, have been got.
对带有初始挠度加劲薄板的临界载荷、极限载荷、波形的重新分布有了一定的感性认识。
Certain perceptual knowledge to critical load, limit load, waveforms redistributing, which all belong to the stiffened panel with initial defects, have been got.
应用推荐