非常剧烈的爆炸会损坏曲轴箱防爆门，引起机仓着火。
A very severe explosion can damage the crankcase door and cause fire in the engine room.
在安放新过滤器之前，曲轴箱必须滴干。
The crankcase has to drain before you put on the new filter.
主轴箱中等主轴是车床的关键零件。
曲轴箱是发动机气缸体较低的部分。
The crankcase is the lower part of the engine cylinder block .
热量传递曲轴箱并散发热量。
This heat is transferred to the crankcase. Here the heat is dissipated.
水分水汽在井喷的气体可以进入曲轴箱。
Moisture from water vapor in the blow-by gases can enter the crankcase.
我也作出了线程在曲轴箱举行缸在地方。
I also made the thread in the crankcase to hold the cylinder in place.
曲轴箱连杆密封件损坏。
有几种方法，使曲轴箱。
其中一半的负面模具和'内的曲轴箱'展开。
One half of the negative mould and the 'inside of the crankcase' mounted.
在场的分散剂和洗涤剂增加发泡趋势曲轴箱油。
The presence of dispersants and detergents increase the foaming tendency of crankcase oil .
曲轴箱通风系统要携带新鲜的空气通过曲轴箱。
The crankcase ventilation system carries fresh air through the crankcase.
曲轴箱通风系统要携带新鲜的空气通过曲轴箱。
The crankcase ventilation system carries fresh air through the crankcase .
我这样说是因为后来当我机曲轴箱我的一些离开。
I say this because later when I machine the crankcases I take some away.
内侧轴箱式转向架是一种新型结构模式的转向架。
The inside axle box type bogie is a bogie with new type of structure.
本文就机床主轴箱的瞬态温度分布提供一个近似解。
This paper presents an approximate solution of instantaneous temperature distribution of the headstock.
当我现在要多作蜡后方进气曲轴箱，我有一些工作。
When I now want to make more wax rear intake crankcases I have some work.
有始终是一个借口，当你的工作与这种既定的曲轴箱。
There is always an excuse when you are working with such established crankcases.
双方曲轴箱，建立了由失蜡法这意味着你必须作出负面的模具。
Both crankcases are established by the lost WAX method which means that you have to make a negative mould.
油盘和气缸体的下部一起被称为曲轴箱，用来封闭或罩住曲轴。
The oil pan and the lower part of the cylinder block together are called the crankcase; they enclose, or encase, the crankshaft.
汽车内泄漏污染物的四个位置是燃油箱、化油箱、曲轴箱和尾管。
The four places in the automobile from which pollutants can escape are the fuel tank, carburetor, crankcase and tail pipe .
具体用法是把清洗剂倒入曲轴箱，怠速5到10分钟后，排出旧机油。
The usage is the cleaning agent into the crankcase, idle for 5 to 10 minutes, drain the old oil.
因此，没有证据显示这些液体机油来自曲轴箱通风和停留的各种装配管道…
So there is no evidence to show the liquid oil come from crank case ventilation and remain in the manifold assembly .
如果没有机油，压缩的气体会从曲轴箱溢出，这会对发动机的性能带来影响。
Without the oil, compression games would escape into the crankcase area, which will make effect on the performance of the engine.
由于高公差内曲轴箱不过，这可以是一个困难的，往往不是非常精确的任务。
Because of high tolerances inside the crankcase however this can be a difficult and often not very precise task.
根据模块化设计原理，在功能分析的基础上划分了组合机床多轴箱的各级模块。
According to modularization design principle, the modules of multi-spindle box of modular machine tool are divided on the basis of function analysis.
根据模块化设计原理，在功能分析的基础上划分了组合机床多轴箱的各级模块。
According to modularization design principle, the modules of multi-spindle box of modular machine tool are divided on the basis of function analysis.
应用推荐