文中分析了使用偏轴接头对钻具各部分受力情况的影响及导致钻具失效的原因。
This paper analyses the influence of excentric shaft connection on force case of drill tool, and discusses the causes of drill tool failure.
为了达到较好的防斜目的，必须增大钻进时钻头的转速，在高转速的作用下，偏轴接头加剧了钻具先期疲劳失效。
By the action of high roatry speed, excentric shaft connection intensifies the fatigue failure of drill tool.
该模型能够用于求解钻头处的侧向力和转角以及偏轴接头处的侧向力，以评价钻具组合的防斜（纠斜）能力和偏轴接头附近的偏磨程度。
The lateral force on offset-axes sub can be calculated and used to evaluate the eccentrically wearing degree near the offset-axes sub.
硅树脂前轮驱动轴CV接头防尘套在运行中会出油，并在前轮驱动轴CV接头防尘套的外侧形成一层薄薄的油脂膜。
The silicone front wheel driveshaft CV joint boot will sweat during operation, causing a light film of grease to show on the outside of the front wheel driveshaft CV joint boot.
结果表明焊接接头裂端应力三轴性随焊缝和母材匹配性质及裂纹几何不同而变化。
The numerical results show that the stress triaxiality varies with the mis matching mode and crack geometry of welded joints.
本文对三种新型钢轨接头现场使用情况的测试结果进行了介绍，主要包括测点处的钢轨接头夹板上、下缘动弯应力、夹板水平中性轴处剪应力。
The testing results about the use of new rail joint was introduced, which include the dynamic flexure stress of upper limb and lower margin of joint bar, shearing stress of horizontally neutral axis.
特别设计的工艺，充分体现了两支轴的良好同心，热媒及真空系统均采用可靠的机械密封或美国技木的旋转接头。
The specially designed process fully shows the good concentricity of the two shafts. Thermal media and vacuum system all adopt reliable mechanical sealing or rotating connector of American Technology.
在万象头和伸缩接头的应用下，传动轴还能进行收缩，伸展或改变运行角度等方式来传递扭矩。
The drive shaft is able to contract, expand, and change operating angles while transmitting torque through the use of universal joints and slip joints.
所述浮动称重筒与无轴螺旋机本体的出料口通过软接头连接。
The floating weighing barrel is connected with the material discharging opening of the non-axle spiral conveyor main body through a flexible connector.
通过对焊接接头组织的分析，发现焊核区晶粒为明显的细化再结晶等轴晶；
The microstructure of the welded joints was studied by optical microscopy. It is found that the weld nugget has a dynamic recrystallization, fine isometric crystal structure.
在接头正常运行过程中，上述第二轴可通过测试元件进行旋转。
The second shaft is rotatable via the test element during normal operation of the joint.
结构上以模块化设计为特点，拧紧轴分为电缆接头模块，马达模块，减速模块，传感器模块，信号预处理模块，输出轴模块。
It features module designing, the spindle is composed of connector, motor, gear box, transducer, signal processing, and output shaft module.
太糟糕，我从来没有一轴螺纹接头听到…
当第一轴不起作用时，上述第二轴处理作用在铰接接头上的负载，并且因此不能通过测试元件旋转，这样指示所述第一轴出现故障。
When the first shaft is inoperable, the second shaft handles loads acting on the articulation joint, and is not rotatable via the test element, thus indicating a failure of the first shaft.
发动机是提供动力的组件，一般装在汽车的前面，紧接着离合器、变速器、传动轴、万向接头、差速器、后车轴等等。
The engine acts as the power unit located normally at the front of the car, followed immediately by a clutch, gear box, propeller shaft, universal joint , differential, back axle, etc.
本实用新型涉及一种压装轴连接头装置，属于电机生产工装的技术领域。
The utility model relates to a connector device of a press mounting shaft, which belongs to the technical field of motor frock manufacturing.
它可有效保证连接头与轴被压装到位且不会造成连接头、轴及减速箱 损坏。
The device can effectively guarantee a connector and a shaft to be perfectly pressed and can prevent the damages of the connector, the shaft and a speed reduction box.
通过单轴拉伸与平面拉伸试验，得到了柔性接头弹性件橡胶材料“三阶五项式冶超弹本构模型参数，通过有限元计算证明了该模型的优越性。
Planar and uniaxial tests were implemented to achieve 3nd order 5th item strain model constant of theelastomer and it is proved this model was superior to others.
两端的轴1有一个辅助焊接头3也是动产的横向和纵向的已知手段平方毫米。
At each end of the shaft 1 there is an auxiliary welding head 3 which is also movable horizontally and vertically by known means MM2.
两端的轴1有一个辅助焊接头3也是动产的横向和纵向的已知手段平方毫米。
At each end of the shaft 1 there is an auxiliary welding head 3 which is also movable horizontally and vertically by known means MM2.
应用推荐