标高是轴承载荷最主要的影响因素。
Bearing elevation is the major factor that influences the load distribution.
本文阐述了三牙轮钻头滑动轴承载荷的测试方法。
A method of determining the load on journal bearing of three-cone bit is described in this paper.
由此引起的轴承载荷的增加会缩短轴承的使用寿命。
The resulting increased bearing load shortens bearing service life.
研究了游隙对单排四点接触球转盘轴承载荷分布的影响规律。
The influence law of clearance on load distribution of single row four-point contact ball slewing bearings is researched.
深沟球轴承主要承受径向载荷，也可承受一定量的轴承载荷。
Deep groove ball bearings mainly take radial load as well as take moderate axial load.
轴承接触角和滚子半圆锥角是影响轴承载荷和使用寿命的两个重要参数。
The bearing contact Angle and the roller half taper Angle are two important parameters of a large taper conical roller bearing, they influence the load and life of the bearing.
曲轴上平衡重的安装减小了曲轴所受的弯矩，但也影响了主轴承载荷的大小和分布。
The counterweight is installed on the crankshaft for reducing the bending moment on it, but it will influence the magnitude and distribution of the main bearing load.
选择合适的调节阀重叠度能够提高调节级效率；合理的开启顺序可以减轻轴承载荷。
Choosing proper opening lap value between governing valves can improve governing stage efficiency.
合理地布置平衡重的位置以使主轴承载荷的最大值达到最小，这是平衡重设计的又一问题。
The reasonable disposition of the crankshaft counterweight can minimize the maximum load on the main bearing, it is another problem of the design of the counterweight.
除了控制的机械轴和轴承载荷，耦合进一步保护通过提供电力和热轴之间的耦合隔离高度编码器。
In addition to controlling mechanical shaft and bearing loads, the coupling further protects the encoder by providing a high degree of electrical and thermal isolation between coupled shafts.
针对传感器弹性体的重要性，本文应用有限元分析软件ANSYS对二维轴承载荷传感器弹性体进行了结构优化设计。
Aiming at the importance of the elastomer, based on the ANSYS, the thesis has realized the structure optimization design of the elastomer of two-dimensional bearing load cell.
建立了含有虚约束的多相并列平行曲柄机构受力分析模型。在此基础上分析计算了三环减速器的轴承载荷和高速轴曲柄上的转矩；
The load of planetary bearings and the moment in the high speed shafts are analyzed and some suggestions about the structure type and design parameters of the three ring reductor were a…
本文利用拟动力学法，同时考虑径向负荷、轴向负荷、自身离心力以及陀螺力矩作用的影响，建立了高速滚珠轴承载荷分布的分析模型。
Considering radial load, axial load, centrifugal force and gyroscopic moment acted on the ball bearing simultaneously, an analysis model based on quasi-dynamic method was set up in this paper.
向心关节轴承在承受载荷时，承载区各点的压应力是不等值的。
When absorbing load, various loaded points of plain radial bearing receive different compressive stresses.
并以点和直线的斜率举例说明绘制转盘轴承静载荷承载曲线的全过程。
The practical examples of point and line slope are given to show the complete procedure of drawing static load curve of the turntable bearings.
其中挤压运动反映轴承在变载荷条件下，承载油膜抵抗拉应力的能力。
And the squeezing movement reflected the ability of oil to resist the tensile stress.
链结子为换向机构，具有滑动轴承功能，并联循环链和主传动链，把循环运动变为上下往复运动。承载链直接承受平衡载荷，可大幅度减小主传动链的受力。
The chain link is the reverse mechanism, functions as sliding bearing and makes the cycle chain and main drive chain parallel to change the circulation into reciprocation.
链结子为换向机构，具有滑动轴承功能，并联循环链和主传动链，把循环运动变为上下往复运动。承载链直接承受平衡载荷，可大幅度减小主传动链的受力。
The chain link is the reverse mechanism, functions as sliding bearing and makes the cycle chain and main drive chain parallel to change the circulation into reciprocation.
应用推荐