作用于平行轴承轴心线方向的负荷。
Acting on the bearing axis line parallel to the direction of the load.
作用于垂直轴承轴心线方向的负荷。
Acting on the vertical axis line direction of load bearing...
平行于轴承轴心线的方向。
有径向凸缘及在与轴承轴心线垂直的支承表面上有供其安装用的螺钉孔的一种座。
A radial flange and in line with the bearing axis perpendicular to the bearing surface for the installation of a screw hole with a seat.
向心轴承与座组合在一起的一种组件，在与轴承轴心线平行的支撑表面上有供安装螺钉的底板。
Radial bearing seat together with a component, in line with the bearing axis parallel to the surface, there is support for the mounting screws of the bott...
向心轴承与座组合在一起的一种组件，在与轴承轴心线平行的支撑表面上有供安装螺钉的底板。
Radial bearing seat together with a component, in line with the bearing axis parallel to the surface, there is support for the mounting screws of the bo…
该系统可测量内燃机主轴承的油膜厚度、油膜温度、曲轴转角、转速、轴心轨迹和最小油膜厚度。
It can measure the oil film thickness, oil temperature, crank Angle, speed, journal center locus and minimum oil film thickness of main bearing in diesel engine.
释放轴心和左侧的轴端盖子。之后取出轴承。
计算结果表明，在非线性因素作用下，轴承中心的轴心轨迹不再具有对称性，而轴颈中心却表现为一种稳定的运动状态。
The results shown that, with the effect of nonlinear components, the symmetry of rotation trajectory of the bearing center was broken, and the motion of the journal center presented a steady state.
圆锥滚子轴承内圈(外圈)的轴心线。
Tapered roller bearing inner ring (outer ring) of the axis line.
在轴承径向平面内通过轴心线的方向。
In the bearing radial plane through the axis line direction.
轴承轴向平面是包容轴心线在内的平面。
Bearing axial plane is the plane including the axis line of tolerance.
级别2：轴承更换。轴心更换。
研究了非线性弹性转子-轴承系统的轴心轨迹，认为对称不平衡转子是连续弹性轴，它两端支撑在滑动轴承上，油膜反力采用非线性短轴承模型。
With reference to a symmetrical unbalanced rotor treated as a continuous elastic shaft suPPorted at its end by lubricated journal bearings, the short bearing model is adoPted.
滚动轴承的理论旋转轴心线，对向心轴承即内圈轴心线，对推力轴承则指轴圈轴心线。
Rolling theoretical rotation axis line of the inner ring to the center axis line of bearings, thrust bearings on the shaft circle refers to the axis line.
轴承内圈(轴圈)的基本圆柱孔或圆锥孔的内接圆柱体或内接圆锥体的轴心线。
Bearing inner ring (shaft circle) of the basic cylindrical hole or holes in the internal tapered cylinder or cone in the axis line access.
从而，可达到加工简易及可大量生产，还可稳固轴心位置，使在轴承中的轴心保持在中央的位置上。
Thereby, the easy processing and mass production are realized, and the position of the axial center can also be stable for holding the axial center of the bearing on the central position.
该模型在纯扭转模型的基础上，进一步计入了行星轮轴心沿系杆切向的位移与行星轮轴的轴承支承刚度对系统动力学性能的影响。
Compared with the purely torsional model, tangential displacements and bearing stiffness of the pinions are included in the governing equation of motion.
数值结果表明，同轴承长径比及转子质量偏心相比，轴颈间隙是影响系统轴心轨迹和频域特性的主要因素。
The result shows that compared with slenderness ratio of bearing and the eccentricity of rotor, the journal clearance is the main factor influencing the trajectory and domain characteristics.
角接触球轴承，轴承的负荷，在一定的角度，-所谓的“接触”轴心线(参见下图)的角度转移。
Angular contact ball bearings transfer the loads acting on the bearing at a certain Angle, the so - called "contact" Angle from the shaft centre line (see sketch below).
角接触球轴承，轴承的负荷，在一定的角度，-所谓的“接触”轴心线(参见下图)的角度转移。
Angular contact ball bearings transfer the loads acting on the bearing at a certain Angle, the so - called "contact" Angle from the shaft centre line (see sketch below).
应用推荐