轴承制造商应对表3中给定的载荷和规定转数进行疲劳计算。
The bearing manufacturer shall make a fatigue calculation accounting for the loads given in table 3 and the specified number of revolutions.
考虑钻机(水)龙头和转盘主轴承工作载荷的模糊性及可靠性要求，应用模糊数学基本原理求得平均计算载荷，从而计算出主轴承的模糊可靠性寿命。
The mean value of work loads on a shaft bearing of swivel and rotary table is determined by basic principles of fuzzy theory, considering the loads' fuzziness and the requirement for reliability.
通过计算承受联合载荷的圆锥滚子轴承负荷分布，分析了在不同偏斜状况下圆锥滚子及滚道受力的变化趋势，总结出偏斜对圆锥滚子轴承受力的影响。
Calculates the load distribution in a tapered roller bearing under combined loads, and analyzes the effect of misalignment on the loads in a tapered roller and raceways.
其次，由轴向定位预紧轴承受径向载荷时各滚子的变形，推导出轴承的径向刚度计算公式；
Second, the calculation formula of radial rigidity is deduced according to the deformation of rollers under the radial load with axial position preload.
考虑钻机水龙头和转盘主轴承工作载荷的模糊性及可靠性要求，应用模糊数学基本原理求得平均计算载荷，从而计算出主轴承的模糊可靠性寿命。
The mean value of work loads on a shaft bearing of swivel and rotary table is determined by basic principles of fuzzy theory, considering the loads' fuzziness and the requirement for reliability.
应使用轴承可能承受的最大载荷计算轴承当量静载荷。
The maximum load that can occur on a bearing should be used in the calculation of the equivalent static bearing load.
采用基于轿车线性化刚体运动的稳态转弯模型对轮毂轴承外部载荷进行推导计算，进而对轴承外部载荷的特性进行了分析。
A method to determine the cars wheel-bearings external load (CWEL) was developed from this model and the characteristic of the CWEL was presented.
然后，以两套具有不同几何参数及外部载荷的轴承为例，利用静力模型计算了轴承的载荷分布。
Then, two bearings having different geometrical parameters and external loads are used as cases, the loads distributions are computed by using the statics model.
利用模糊数学方法，通过模糊综合评判，确定了转臂轴承的模糊平均当量动载荷，并计算了转臂轴承的模糊可靠性寿命。
Fuzzy average equivalent dynamic load of arm bearing is calculated by using fuzzy mathematics method and fuzzy comprehensive evaluation. Fuzzy reliability life of arm bearing is calculated.
建立了含有虚约束的多相并列平行曲柄机构受力分析模型。在此基础上分析计算了三环减速器的轴承载荷和高速轴曲柄上的转矩；
The load of planetary bearings and the moment in the high speed shafts are analyzed and some suggestions about the structure type and design parameters of the three ring reductor were a…
建立了含有虚约束的多相并列平行曲柄机构受力分析模型。在此基础上分析计算了三环减速器的轴承载荷和高速轴曲柄上的转矩；
The load of planetary bearings and the moment in the high speed shafts are analyzed and some suggestions about the structure type and design parameters of the three ring reductor were a…
应用推荐