更大的接触角型具有较好的轴向负荷能力。
单列角接触球轴承可承受径向，轴向或复合负荷，不过，任何轴向负载必须在一个方向。
Single-row Angular Contact ball bearings can sustain radial, axial or composite loads, however, any axial load must be in one direction.
圆锥滚子轴承系列313，特别是足够的，由于其相对较大的接触角(约30摄氏度)，高轴向力时要考虑的。
Taper roller bearings of the series 313 are particularly adequate due to their comparatively large contact Angle (approximate 30 deg), when high axial forces are to be considered.
单向和双向推力角接触球轴承（图1.50和1.51）都用机床主轴轴向刚性作为指导。
Single-direction and double-direction angular contact thrust ball bearings (Figures 1.50 and 1.51) are used for machine tool spindles requiring rigid axial guidance.
由于其接触角，单列角接触球轴承比深沟球轴承更适合维持高轴向负荷。
Due to their contact Angle, single-row angular contact ball bearings are better suited to sustaining high axial loads than deep-groove ball bearings.
结果表明，最大压应力轴向分布呈S形，原辊形会引起接触应力集中。
The calculated results indicate that the axial distributions of the maximum contact pressure have an "s" shape.
提出了用圆筒两端加制法兰与端盖平面接触轴向螺栓连接的方法设计大扭矩磁滑轮的方案。
The new scheme is put forward to design magnetic pulley with large torsional moment by means of planar contact between end-cover and added flange fixed axially by stud bolt.
四点接触球轴承多用于轧钢机的油辊箱以承受轴向负荷。
Four-point contact ball earings used for rolling mill roll the oil tank to withstand the axial load.
研究了轴向坐封载荷与胶筒的峰值接触压力和轴向压缩量之间的变化规律。
The laws between axial set-down loads and maximum contact sealing pressure, and axial compressed displacement were studied.
作者以轴向迷宫式密封和径向接触式密封为例，介绍了安装技巧和要点。
The author introduced installation technology and skill with the examples of axial labyrinth seal and radial contact seal.
当轴承的径向游隙加大时，具有角接触轴承的功能，可承受较大的轴向负荷。
When bearings radial clearance increase with angular contact ball bearings of the feature, may withstand the big axial loads.
本文主要阐述了角接触轴承的安装形式及其轴向游隙在实际应用中的影响，并介绍了相应的应对措施。
This article explains mainly installation form of angular contact ball bearing and its axial backlash influence in practical application, and introduces the corresponding counter-measure.
电接触被保持在支撑体上，并且可以是从凸缘面延伸的轴向对齐的针脚。
Electrical contacts are held on the support, and may be axially aligned pins extending from the face of the flange.
DB组合，DF组合及四点接触、双列角接触球轴承可承受径向和双向轴向负荷。
DB combinations, DF combinations and four-point contact, double row angular contact ball bearings can withstand radial and bi-axial load.
圆弧齿轮传动是一种轴向共轭、点啮合制的齿轮传动，运动的传递依靠接触迹沿轴向移动实现。
The circular arc gear drive is one kind of axial conjugate gear drive which meshes in points. The movement transmission depends contact mark along the end motion to realize.
高接触角带有相当的轴向载荷。
本文研究了自动调心分离轴承装置的结构和调心原理，分析了弹性元件载荷与变形的关系，给出了分离轴承接触角和极限轴向负荷的确定方法。
The relation between load and deformation of the spring element is analysed and the calculating methods of constant angle and maximum axial load are set up.
较小的双列角接触球轴承没有填充槽(图1.15a和b)，使他们可以从双方的轴向加载。
Smaller double-row angular contact ball bearings do not have a filling slot (Figure 1.15a and b) so that they can be axially loaded from both sides.
对转台中环主轴施加轴向定位预紧力，通过脉冲激励法试验得到角接触球轴承的轴向刚度，试验结果与理论结果吻合较好，为转台研制中各轴系预紧量的控制提供了理论和实验依据。
The axial fixed position preload is applied to middle ring of the shaft, the axial rigidity of the angular contact ball bearing is obtained by the impulse excitation tests.
钢管周向和径向的应力值不大，而轴向应力值较大，最大轴向应力出现在钢管与芯模的接触部位。
The axial stress on the steel tube which appears on the contact region of the steel tube and mandril is larger than the radial and circumferential stress.
四点接触球轴承为可分离型轴承，可承受双向轴向载荷，并有单列和双列角接触球轴承的功能。
Four pionts Angle contact ball bearing is separable bearing, it can be subject to bi-directional load and have the function of both single row and double rows bearings.
但由于中间辊轴向窜动后，在工作辊与中间辊、中间辊与支撑辊间形成接触压力峰值，导致轧辊局部磨损及带材表面质量问题。
But the peak of contact pressure between rolls forms when the intermediate roll shifts, which leads local wear of rolls and quality defects of strip.
单列角接触轴承背对背的配对形式，可承受两个方向的轴向载荷，同时可承受径向载荷。
Double row angular contact ball bearings are a form of back-to-back pairs of single row angular contact ball bearings, which support axial load in both directions as well as support radial load.
基于现有的单螺母滚珠丝杠副弹性变形理论基础，建立了滚珠丝杠副弹性接触变形的模型并得到改进的轴向变形公式。
Based on the current elastic deformation theory of single-nut ball screw, a model of ball screw was developed and a modified formula of axial deformation of ball screw was derived.
径向载荷和轴向载荷对接触角的变化影响较大，直接关系到滚珠轴承的失效情况；
The radial and axial loads affect the ball contact angles relating to the bearing failure.
径向载荷和轴向载荷对接触角的变化影响较大，直接关系到滚珠轴承的失效情况；
The radial and axial loads affect the ball contact angles relating to the bearing failure.
应用推荐