需用电脑串口软件调试。波特率9600。
You need to use computer software debugging port. 9600 baud rate.
系统软件的构成和功能以及软件调试和运行。
The construction and functions of the system software, its debugging and running are also explained in detail.
最后给出了数字控制器硬件、软件调试方法。
Finally, the method of system debugging of hardware and software are analyzed.
本方案已经通过硬件、软件调试以及电路测试。
It has passed the hardware and software debug and circuit test.
探讨FMS运行控制系统软件调试环境的建立问题。
Establishment of testing environment for FMS control software is discussed.
描述供机载雷达应用软件调试、测试用的软件仿真系统。
This paper describes the simulation system for debugging and testing of air borne radar application software.
远程软件调试已经成为嵌入式操作系统调试的重要手段。
Remote cross debugging has become an important debugging means in embedded operating system.
通过软件调试，得到了正确的波形，验证了该算法的可行性。
By debugging the software, the paper reaches correct conclusion, and proves the feasibility of the algorism.
最后，还对系统性能进行硬件和软件调试，证明了系统的可行性。
At last, the performance of the system is tested by circuits and software. The result show that the system works well.
本文对其系统原理、硬件构成、系统配置和软件调试等进行了介绍。
This article focuses on such introductions as its system principles, hardware formation, system disposal and software adjustment.
在硬件电路制作和驱动等软件调试工作完成后，该平台被应用于实际当中。
After the work of making hardware and debugging driver software is completed, the platform is used in practice.
使用本系统完成从软件调试到硬件扩展等多组实验，满足教学实践的需要。
It can be used to complete groups of tests, from the software debugs to the hardware expansion, so the practice teaching requirements can be satisfied sufficiently.
通过硬件和软件调试，并针对问题分析修改后，游戏机系统可以稳定运行。
After the testing of the hardware and software and analysising and amendmenting the problem, the game system can run stably.
嵌入式系统开发过程中，目标软件调试工作最终需要采用交叉调试方式进行。
In the development process of embedded system, object software needs to be debugged by means of cross-debugging.
第二章任务级软件调试需求分析，内容包括系统的主要功能、实现环境、开发限制等。
Chapter 2 presents the requirement analysis of task-level debugging software which consists of the main function, implementation environment and the development limits of the system.
然后，简要地叙述了系统的调试，包括硬件调试、软件调试，并给出了系统的调试结果。
Then, the paper briefly describes the system debugging, including hardware debugging, software debugging, and gives the system debugging result.
介绍了该系统的网络结构方案、软件调试与设置、对用户的管理与授权及信息安全措施。
This paper introduces the network construction, the software setup, user management and authorize, and information security measurement.
本文介绍了基于NETBIOS的网络软件调试工具系统的设计思想、系统结构、模块功能。
In this paper we introduce the designing idea, architecture and functions of modules in the network's software debugging tool system based on NETBIOS.
第四章是任务级软件调试代理关键技术分析。内容包括实现任务级调试主要技术难点和解决方案。
Chapter 4 specifies the key technology analysis of task-level software debugging agent, including the pinch point of the task-level debugging technology and the solution.
软件方案开发，算法设计与优化，源代码编写，软件调试，软件使用说明，以及软件详细设计说明等；
Software scheme development, algorithm design and optimization, source code compiling, software debug, application document and detailed design document creation, etc.
同时对该射频传输模块的软件基本结构做了简要说明，重点对软件调试中遇到的几个难点问题做了分析讨论。
At the same time, it gives a brief account about the basic software configuration of the RF module, several problems which encounter in the software debugging is analyzed emphatically.
本文介绍了在嵌入式调试器中如何通过以太网口进行嵌入式软件调试，实现了主机与开发板之间的网口通信。
This paper introduces how to debug embedded software by Ethernet interface in the embedded debugger. The network communication between the host computer and the board has been implemented.
最后，利用软件编译环境编写各个模块与处理器的接口函数，从而完成系统功能的集成调度，并进行软件调试，最终完成课题。
Finally, compiled interface functions of each module and processor by the software debugging, complete the integrated scheduling of the system, and finally accomplished the study.
软件设计采用了模块化和标准化设计，这样一方面便于软件调试，另一方面便于维护和更新，同时文中还给出了部分主要程序。
The software design makes use of the modulation and standardization, and it is advantageous for software debugging, maintenance and function enhancement, and simultaneously gives subprogram.
依照通用编程规范和模块化编程思想，利用MATLAB编写生成了标准的COM测距组件，有利于程序的移植调用和后期的软件调试。
In accordance with the modular programming ideas, standard com components of fault location are generated using MATLAB language. It is convenient to transplantation and debugging.
完成了基于汇编语言的软件设计，在DSP开发平台CCS2.0下完成了软件调试，实验结果证实了提出的方案的有效性，避免了系统振荡。
Software based on assemble language is finished and debugged successfully under the DSP platform of CCS2.0. Experimental results validate system design above.
最理想的情况是我们能够远程调试软件。
最理想的情况是我们能够远程调试软件。
应用推荐