文章介绍了电路设计的基本原理和软件编制。
The paper also describes the basic principle of the circuit design and the software design.
为软件编制了友好的用户界面，方便用户使用。
The friendly interface is programmed to convenience the users.
较详细地叙述了系统硬件电路构成和软件编制思路。
The system hardware circuity and software programming concept are presented in detail.
为便于实现，提出了面向对象的现场总线应用层软件编制模型。
In order to implement easier, software programming model of object-oriented field bus application layer is stated.
介绍了一种出租车辆调度与管理系统的硬件设计原理和软件编制。
The hardware design and software programming of a taxi dispatching and managing system has been introduced.
然后，利用MATLAB软件编制了初始结构参数快速计算程序。
Then, the initial parameter computing program was programmed using MATLAB software.
介绍了增量式和绝对式编码器在同步丝杆控制中的应用和软件编制。
This paper introduces applications of the incremental and absolute angular encoders in synchronous leading screw control.
完成了电控单元的硬件设计，软件编制调试以及系统改进和完善工作。
The designing of hardware, programming and debugging of software and improvement of the electronic control system were accomplished.
采用MATLAB计算软件编制了相应的程序，得到了方程的数值解。
And the numerical solution was obtained through the corresponding procedure with MATLAB.
并讨论了该控制系统硬件结构及软件编制过程中的一些技术细节及特点。
Then some technical details and characteristics in hardware structure and applied software are discussed.
本文主要介绍了一种新型的四线电话语音信箱的系统硬件设计和软件编制。
The hardware and software designs of a four-line telephone voice mail - box system are introduced in this paper.
采用文献法、问卷调查法、教学实验法、数理统计法、软件编制法等研究方法。
Methods the literature study, questionnaire survey method, teaching experiments and mathematical statistical method, software development method and other methods.
采用现在最流行的多媒体软件编制了核工程仿真演示平台，取得了较好的教学效果。
In order to teach and the train the nuclear power plant workers, the research workout the nuclear engineer simulate demo platform by multimedia technology and get the better teaching effect.
根据钢筋混凝土理论和ANSYS有限元软件编制了实验梁受弯荷载效应模拟计算程序。
A numerical simulation program for flexural load effects of rc beams was compiled based on the theory of reinforced concrete and finite element software ANSYS.
详细阐述了研制过程中的三个方面的问题：硬件实现与调试、软件编制与调试、抗干扰方法。
Questions about three aspects were narrated at length: designing and debugging of hardware system, designing and debugging of software, designing of anti-jamming.
其中计量精度控制方法、硬件设计方法和软件编制方法来自于工程实际，有一定的参考和实用价值。
The measurement accuracy control, hardware design and software engineering preparation method are from the projecting practice, which provides some reference and practical value.
研制了电磁斥力驱动的控制系统，完成了控制电路等的硬件系统设计、制版、调试与系统的软件编制。
Developed the control system of the devices by the mode of electromagnetic repulsion. Finished the design, PCB and debugging of the hardware and the software programming.
报表登记、表样设计、定义取数公式、表页管理、生成利润表是主流财务软件编制利润表的基本程序。
Basic procedure of mainstream financial software profit form making is report form registration, table-like design, definition of picking-number formula, table management, profit form generating.
此类放大器具有通用性强、软件编制容易，精度高等优点，可广泛运用于低频智能仪器及工业控制中。
These types of amplifiers have the characterristics of being universal, easy to program and high accuracy. They can be applied in low-frequency in. tellegent instruments and industry control systems.
文中重点叙述了在线系统的硬件配置及软件编制思想，同时指出了系统仍然存在不足与今后改进的方向。
The paper presents, in particular, the hardware configuration, software for on-line system, including some drawbacks to be solved.
介绍一个由STD微机组成的空气压缩机站得机监控系统的功能及其构成、系统软件编制、抗干扰措施等。
This paper describes an STD microcomputer-based monitoring system for air compressor station including its system functions, constitution, system software structure and anti-interference measures.
以用单片机制作智能酸度计为例，介绍了基于单片机的智能仪表的一般原理、系统结构及其软件编制流程。
By taking pH meter made of MCU as an example this article introduces the general principle system structure and software making process of intelligent meters.
文章介绍了DS12887的内部结构和应用方法，以及由其构成的实时定时硬件电路和接口软件编制方法。
This paper introduces the inside construction and applied method of DS12887, furthermore describes the hardware circuit for real-time timing and programmable method for interface software.
软件编制方面给出了详细的软件流程图，利用汇编语言和16位定点C语言混合编程的方法编制了部分软件。
On the side of real tune software, the module software is written by assembly language functions that interface with 16 bits fixed-point C code.
主要介绍了伺服机构计算机辅助测试系统软件的结构、功能和设计方法，以及在软件编制中某些问题的处理方法。
A computer aided test system about servo mechanisms is presented, the design methods, functions and structure of the system software and the process methods of some problems are introduced.
通过分析目前楼宇智能化专业职业教育实训教学中存在的问题，提出了采用组态软件编制实训仿真平台的解决方法。
By analyzing the problems in practical teaching in intelligent building speciality, this paper proposes the solutions of training simulation platform by configuration software.
通过软件编制的程序能够对输入的信号进行采集、判断、分析、处理、运算，最终将结果通过液晶显示器显示出来。
The software procedure can carry on gathering signal , judging, analyzing, processing, calculating and shows the result by the liquid display finally.
介绍应用涡流检测技术测量铝蒙皮拉弯成型回弹量的基本原理与特点，以及应用系统机实现测量的电路设计与软件编制。
Eddy current testing for measuring rebound clearance of aluminum skin caused by bending is described including its basic principles, characteristics and the design of measuring circuit and software.
介绍应用涡流检测技术测量铝蒙皮拉弯成型回弹量的基本原理与特点，以及应用系统机实现测量的电路设计与软件编制。
Eddy current testing for measuring rebound clearance of aluminum skin caused by bending is described including its basic principles, characteristics and the design of measuring circuit and software.
应用推荐