工作转台速度的调节，是通过变频调速装置，在电气操作柜上，用旋钮进行平稳的调整。
The rotation speed of turntable is adjusted by VVVF facility through a knob in electric panel.
通过转台的非线性动力学模型建立了转台速度环以及位置环的T - S模糊模型，设计了实现速率定位功能的速度环鲁棒最优控制器。
The T-S fuzzy models of the velocity loop and position loop are constructed via the table's nonlinear dynamic model. Robust-optimal controller of velocity-loop is designed for velocity orientation.
试验结果表明，利用三轴转台可以成功地将陀螺加速度表测试精度提高一个数量级。
The test results show that the PIGA's test precision can be improved one order higher using three-axis turntable.
本文讨论了将模型跟踪综合技术用于单轴液压速度转台综合设计的四种方法。
In this paper four model following approaches are used to design Hydraulic Velocity Flight Simulation Table with One Axis.
标准转台等旋转体在转动时产生的角速度波动对被标定设备的数据可信度有很大影响。
When standard turntable runs, its Angle speed fluctuation is critical for the reliability of calibrated device.
在分析和研究加速度计动态输出的基础上，综合了加速度计仿真模型和三轴转台数学模型以及测试误差的特性。
Based on analysis and study the dynamic output of accelerometer, simulating model of accelerometer, mathematical model of three-axis turntable and the characters of test errors are synthesized.
在操作过程中，转台旋转速度，填充深度和压片厚度可作调整。
During operation, the rotation speed of turntable, the depth of filling material and the thickness of the tablets can be adjusted.
首先在分度头上标定加速度计，得到其零点和灵敏度，然后分别在离心机和转台上进行转速实验。
First we calibrate the accelerometers on dividing head to get the offset and sensitivity, then do the rotation experiments on centrifugal machine and rotating floor.
分析了三轴转台设备误差源；讨论了转台误差对陀螺加速度表测试精度的影响。
The error source of the three-axis turntable is analyzed, which affect the precision of test of pendulous integrating gyro accelerometer (PIGA).
利用MATLAB进行了仿真，使得在三轴转台上标定加速度计动态误差系数有了清晰的先验认识和结果预期。
As the result of simulating finished with MATLAB, clear prior knowledge and anticipated result of calibrating dynamic error coefficients of accelerometer on three-axis turntable are obtained.
在三轴转台的三个轴上同时施加恒定角速率，激励出加速度计动态误差项。
The constant angular rate was applied to three axis of turntable at the same time to actuate dynamic error term of accelerometer.
三轴飞行模拟转台是用于飞行控制系统半实物仿真的高性能位置跟踪和速度跟踪的一个重要设备。
The 3-axis flight table is an important device and a typical high performance position and speed servo system used in the hardware-in-the-loop simulation of flight control system.
第三，在地面进行加速度计的三轴转台实验。
Test the accelerometers which is fixed in three-axis rotary table on the ground.
通过对模拟仿真台在不同运动速度时的二维转台动态跟踪实验结果分析表明模拟演示系统有较好的跟踪精度。
The dynamic tracking experimental curves of two-dimension rotating floor, which are acquisitioned in different movement velocities of simulation, imply the better tracking accuracy of the system.
理论分析和实验研究证明采用感应同步器跟踪型测角系统检测位置和速度信号是可行的，在仿真转台的研制中应用该系统是很成功的。
The theory analysis and experiment work proved the hybrid sensor method is correct. And the application of the tracking measuring angle system designed with the new method is …
理论分析和实验研究证明采用感应同步器跟踪型测角系统检测位置和速度信号是可行的，在仿真转台的研制中应用该系统是很成功的。
The theory analysis and experiment work proved the hybrid sensor method is correct. And the application of the tracking measuring angle system designed with the new method is …
应用推荐