轧制速度对界面结合的影响不明显。
提出进一步改造中采用加大盘重、提高轧制速度的可行性。
The possibility of increasing coil weight, raising rolling speed has been analyzed.
而控制冷却可采用全线的温度控制、时间控制、轧制速度来实现。
But Controled cooling USES temperature control, time control on the whole line and speed of rolling.
随着轧制速度的提高，成品终轧温度明显升高，头尾温差大幅度减小；
It is found that, with the rising of rolling speed, the temperature of finished product is raised greatly, and the temperature difference between head and end of the product is reduced apparently.
借此方法研究了轧制油粘度、轧制速度与压下率对轧制变形区油膜厚度的影响。
The influence of the foiling oil viscosity and rolling speed and reduction rate on the film thickness are investigated with those methods.
工作辊磨损后，粗糙度递减导致在较高轧制速度下进料(咬入带卷)时产生滑移。
When work rolls become worn the roughness is diminishing creating slippage in the roll bite at higher speeds.
通过对轧辊与轧件相对速度的分解，作出轧制速度曲线，得出满足轧件不转的条件。
The author draws the curve of rolling speed by decompounding the rolling velocity and obtained the qualification that meets the workpiece not rolling when the 3-roller rolls.
根据极限条件，计算出入口厚度、出口厚度、轧制速度、张力、轧制力、轧制力矩等。
On the basis of the limited conditions, entry thickness, exit thickness, rolling speed, tension, rolling force and rolling torque, etc. are calculated.
详细介绍了圆盘式飞剪各主要参数的确定，包括交角、咬入条件、剪刃重叠量、摩擦系数、轧制速度等。
Setting main parameters of disc flying shears are presented in detail. including cut Angle, bite conditions, amount of scissors overlapping, friction coefficient and rolling speed etc.
近年来，由于轧钢工艺趋向于采用无扭轧制等先进技术，使轧制速度迅速提高，对冷床高速上料装置提出了更高的要求。
In recent years, the speed of rolling has been improved because of the technical trend of no-twist rolling, and the requirement of quick-speed feeding facility on cooling-bed has been put forward.
此模型判断如何选取轧机速度曲线图，首次提出根据轧制变形区各参数来计算不同压下量下的最大轧制速度以及咬入速度。
This model firstly judges how to choose a right curve of rolling speed, then calculate the Max rolling speed and entering speed according to the parameters in deformation zone.
在连轧末机架出口速度一定的情况下，轧制功率的消耗直接影响到能耗指标。
In case of last rolling mill's velocity limited, rolling power affects power consuming index directly.
本文分析了轧制温度、终冷温度、冷却速度以及微合金化对钢筋组织、性能的影响。
The influence of rolling temperature, final cooling temperature, cooling speed and micro-alloying on microstructure and properties were investigated.
通过极限拉伸比试验，研究了轧制、退火、拉伸温度、拉伸速度、拉延间隙以及压边力等工艺因素对镁合金板材成形性能的影响。
Through the limiting drawing ratio tests, the influences of rolling, annealing, blank holder force, drawing gap, drawing temperature and speed on the forming performance were investigated.
该设备能用来测量轧制过程带材的张力和速度，还能用其实现“S”方式轧制时对轧辊的包角调整。
Functions of the device include the measurement of strip tension and mill speed as well as adjustment of flanging the rolled piece with respect to the roll during"S"roiling.
铸轧速度是调节熔池液面高度和轧制力的有效手段。
So, the casting speed plays an efficient role in readjusting the molten steel surface level in pool and rolling force.
异步轧制是以轧辊线速度不对称为主要特点的一种新轧制法。
Asynchronous rolling is a new method of cold rolling of strips.
并研究了轧制不同厚度铝材时，厚度对铸轧速度和温度场的影响规律。
The influence of thickness on cast rolling speed and temperature field were researched.
为了实现正常轧制，在控制粗轧带坯温度、轧制节奏、穿带速度、冷却控制等方面采取了多项措施。
In order to achieve normal rolling, many steps, in controlling transfer bar temperature, rolling rhythm, thread speed and controlled cooling and so on, are taken.
随着芯辊进给速度的增大，轧制力和轧制力矩也相应增大，因此对轧环机力能参数的要求也提高；
The results also predict that the roll force and the roll torque increase with the increase of the feed velocity.
全连续冷连轧机的自动速度控制系统要求通过活套分离开卷运行过程和轧制运行过程以实现全连续轧制。
Automatic velocity control system for the continuous tandem cold mill let the rolling mill work continuously by using the looper to keep the uncoiling operation separating from the rolling process.
速度是轧制中的一个重要因素。
速度制度是轧制规程设定计算的重要组成部分。
Rolling speed is a very important part of rolling schedule in setup calculation.
同时对不同的径向和轴向进给速度对径轴双向复合轧制过程中轧制力，直径增长速率及温度分布的影响进行了系统分析，并进行了相应的实验验证。
Influences of different radial and axial feeding speed on the radial and axial rolling force, growth rate of diameter and temperature have been systematically analyzed and proved by trials.
为提高冷连轧机轧制力的预报精度和预报速度，用蚁群算法和神经网络相结合的方法进行轧制力预报模型设计。
To improve the precision and efficiency of rolling force prediction on tandem cold rolling mill, a neural network model combined with ant colony algorithm is presented.
通过模拟比较，揭示了进给速度和轧制比对双球面环件轧制宽展变形与力能参数的作用规律。
Through simulation and comparison, the influence laws of feed velocity and different rolling ratio on transverse width deformation and force-energy parameters were opened out.
轧制AM60的横向疲劳裂纹扩展速度（FCPR）明显地高于纵向。
The fatigue crack propagation rate (FCPR) of as-rolled AM60 in the longitudinal direction is higher than that of the transverse direction.
本文介绍了速度及张力控制系统在鞍山市轧钢厂万能轧机轧制线上的应用。
This paper presents the application of speed and tension control system in the line of universal mill of Anshan Rolling Steel Plant.
对神经网络模型的仿真测试表明该神经网络轧制力模型有较强的泛化能力，收敛速度快，不易陷入局部最优，精度明显高于传统的轧制力模型。
Simulation result shows that the model has the following merits: definite extend ability, high convergence velocity, not easy getting in local optimization, and higher precision.
对神经网络模型的仿真测试表明该神经网络轧制力模型有较强的泛化能力，收敛速度快，不易陷入局部最优，精度明显高于传统的轧制力模型。
Simulation result shows that the model has the following merits: definite extend ability, high convergence velocity, not easy getting in local optimization, and higher precision.
应用推荐