而且他们走同一条线的两个不同起始方向时也会有不同的感觉。
They would also suffer at the same time in both directions from a different lane feel.
通过理论分析和实验结果，推导了天井内的羽流速度和决定环流起始方向的判据。
Based on the analysis of the experimental results, the plume velocity was deduced, and a criteria for determining the initial direction of the circulation plume was given.
然后文字开始滚动直到到达另一侧，之后改变方向，再滚回它的起始位置。
The text then scrolls until it reaches the other end, whereupon it reverses direction and scrolls back to its starting point.
在加工过程重全面控制每把刀具，包括行程方向及板材的起始角。
Have total control over each tool, including travel direction and sheet starting corner curing sequencing.
利用电磁暂态程序emtp进行机理分析的结果认为：短路电流起始相位的随机性以及互感器铁心剩磁方向的随机性会导致上述现象的出现。
With simulation by emtp it shows that both the random initial phase of short circuit current and the random direction and value of residual magnetism are the reason of above-mentioned phenomenon.
手臂反方向划圈，呼气同时将重物慢慢下放回起始位置，并且慢慢的放下脚跟。
Reverse direction of circles, exhale and lower weights back down to start position and lowering heels.
试样越多，峰顶温度向高温方向偏移，但外推起始温度不变；
The more sample is the more the peak temperature deviates to high temperature, but extrapolated onset temperature is constant.
研究了刷镀起始镀层组织及其影响因素，分析了刷镀方向、刷镀时间、刷镀电压、镀液温度对起始镀层组织的作用。
The microstructure of initial brush plating layer was studied along with its influencing factors as the direction of brush plating, time, voltage and temperature.
方向线的角度决定起始和结束线通过的角。
The angle of the orientation line determines which corners the starting and ending lines pass through.
起始线与方向线垂直，并经过矩形的一个角。
The starting line is perpendicular to the orientation line and passes through one of the corners of the rectangle.
目标化合物以甘油、硝基甲烷为三方向起始核心，以从季碳原子三倍对称分散的化合物1～3为分支侧链。
Three branched monomers 1 ~ 3, possessing 3 - fold symmetry and branches emanating from a tetrahedral carbon branch point, were utilized as the key building block in the dendrimer syntheses.
这里将通常设于外部的扁毛细管节流器移至腔内转动方向的起始处，并通过浅腔再次节流。
In this paper, the flat capillary restrictor is lay in the deep recesses instead of outer space. in other word, the deep recesses ACTS as restrictor, and the shallow recesses throttles again.
试件的疲劳断裂模式全部为双面穿板断裂，疲劳裂纹起始于点焊热影响区搭接板内表面，沿板厚方向向外表面扩展；
Fatigue specimens cracked at two-sided through-thickness sheet, fatigue crack appeared initially in HAZ of inner surface of lap plates, along the thickness direction extended to outer surface;
试件的疲劳断裂模式全部为双面穿板断裂，疲劳裂纹起始于点焊热影响区搭接板内表面，沿板厚方向向外表面扩展；
Fatigue specimens cracked at two-sided through-thickness sheet, fatigue crack appeared initially in HAZ of inner surface of lap plates, along the thickness direction extended to outer surface;
应用推荐