上述研究查明了磨床误差及加工调整参数误差对螺旋锥齿轮齿面误差的影响机制。
The above research finds out the influence of grinder error and machining setting parameter error on tooth surface error of spiral bevel gear.
依据二值化的结果估计滤波的误差，并调整滤波器参数。
Then the filtering error is estimated and filter parameters are adjusted based on the binary data.
这里将网络的总体误差作为目标函数，以待求的所有参数作为变量，同时调整，构成全监督算法。
Defining network error as optimum objective function, all parameters are looked as function variables, and an entire-supervised algorithm is studied.
该控制器能够根据系统的误差、误差变化及误差积分值自动调整控制器的控制参数，使模糊控制器具有自适应的能力。
The parameter of the controller can be auto-adjusted by the error, error change and the integral value. It makes the fuzzy controller have the ability of self-adaptive.
将模糊控制与常规pid控制相结合，根据不同的误差、误差变化率对PID的参数进行在线自动调整，这就是PID参数自整定模糊控制器。
Combine blur control with general PID control, on line self-adjusting PID parameters according to different error and error variety-rate, which is called PID parameters self-tuning blur controller.
结合机床调整参数、齿轮啮合原理，建立了螺旋锥齿轮齿面误差修正模型。
The error correction model of tooth surface was established by machine tool adjustment parameters and meshing principle.
给出了应用实例。还研究了混沌参数与训练误差的关系，提出了混沌参数的调整步骤及应用。
And it studied relation between chaos mapping parameters and training error, puts forward chaos mapping parameter adjust steps and applications.
斜坡根据密度跟踪误差和误差变化情况，通过模糊逻辑对控制器参数进行调整，确定了测量速度。
The ramp metering rate is determined by the PID controller whose parameters are tuned by fuzzy logic according to the density tracking error and error variation.
其基本思想是仿射坐标架中的原点坐标带有两个可以在一定误差范围内变化的调整参数。
The basic idea is. the origin which has two adjustable parameters on the affine coordinate frame and the affine coordinate frame are both active.
在网络参数学习的同时网络结构也在进行调整，使得误差不断减小。
Network structure is adjusted with networks parameter learning, which could reduce error.
学习过程通过调整权值、计算误差、修正隐层单元的参数，以达到最优结果。
Through adjusting weight, computing error rate and modifying the parameters of hidden nodes, optimal results will be achieved in the learning procedure.
螺柱提起高度、送下深度、提起和送下速度等焊接参数的设定由程序控制，减少了人工调整的随机误差；
The setting of welding parameters, involving stud lifting height, stud sending depth, lifting and sending speed and so on, can be accomplished by program control, thus the artificial error is reduced.
在机器人动力学方程存在误差的情况下，能通过文中提出的参数调整规则补偿误差。
Though there are errors during the modeling for the robot dynamics, they can be compensated according to the rule of adjusting weight values.
本文给出了一种新型自适应曲线插补方法。即根据弓高误差自动调整进给步长，同时将轮廓误差限定在允许范围之内的参数曲线实时插补方法。
A new adaptive method about curve interpolation is proposed, which can automatically adjust step-length of motion and confine the contour error within a given tolerance.
为了更好地克服各种外界因素的影响，构造了误差观测器，在线实时调整控制器参数。
To overcome the influence of some outer factors, parameters of controller are adjusted online based on the error observer.
该计算方法根据误差分析对计算参数进行调整后取得了良好的效果。
These parameters were applied in the designing of the crucible and was proved to be feasible.
又将蚂蚁行经路径上的存储单元存放的参数值赋予BP网络训练，而存储单元存放的参数和训练误差值亦随BP网络训练误差的调整而改变。
Parameters value of sites in ants' route was bestowed on BP network, while parameters and training error stored in stored units were changed along with the adjustment of training error of BP network.
又将蚂蚁行经路径上的存储单元存放的参数值赋予BP网络训练，而存储单元存放的参数和训练误差值亦随BP网络训练误差的调整而改变。
Parameters value of sites in ants' route was bestowed on BP network, while parameters and training error stored in stored units were changed along with the adjustment of training error of BP network.
应用推荐