采用非接触光电式测量方法,设计了多工位数控刀架误差测量系统。
An error measuring system for multi-location numerical control cutter holder was developed by adopted non-contact photoelectric measuring method.
为了解决实际生产中大模数滚刀的在线测量,提出一种滚刀容屑槽周节误差测量系统。
To solve the problem of inline measuring hobs with bigger modulus in practice production, an inline measuring system for the circular pitch error of hobs is introduced.
这可让OPERA进行重复测量,以消除可能的系统误差。
This will allow Opera to repeat the measurement, removing some of the possible systematics.
分析了在解码电路实验中,测量波形产生误差的原因,提出了采用有线电视系统传送信号的实验方法。
This paper analyzes reason of measure waveform produce error in decode circuit, put forward experiment means of adopt closed circuit television system transmit signal.
在高压电力系统中,为了提高电压互感器的测量准确度,必须减小误差。
In high voltage power system, in order to raise measurement accuracy, errors must be reduced.
深入分析了引起系统测量误差的原因,并利用神经网络对线结构光测量系统进行误差补偿,提高了系统的测量精度。
The reason that caused measurement error is analyzed deeply. The paper makes use of the neural network to compensate linear structured light measurement system, so improve the measurement precision.
详细分析与估计了系统的测量误差并探索了提高准确度的方法。
The error have been analyzed and estimated in detail and the method to raise accuracy of measurement have been discussed.
本文分析了桥式三座标测量机的系统误差。
This paper analyses the systematic error of three coordinate measuring machine of bridge type construction.
圆度误差值为组建用于动态测量精度理论研究的分析实验系统做准备。
The roundness error serves the preparation for setting up the analyzing experiment system for theory research of dynamic measurement precision.
给出了次测量系统的误差分析。
系统误差(SYSTEMATICERROR)-受系统自身分布误差影响的大量测量结果的平均值与真值的偏差。
Systematic error - the mean of a large number of measurements influenced by systematic error deviates from the true value.
本文主要介绍了以电子经纬仪为传感器的工业测量系统的测量原理,分析了此系统的误差来源及其对精度的影响。
Principle of the industrial system measurement using a theodolite as the sensor is introduced, with sources of error and their effects upon precision analyzed.
光扭矩传感器的输出信号在进行光电转换过程中,由于温度影响,造成了直流电平漂移误差,影响系统的测量精度。
During the photoelectric conversion process of output signal from optical torque sensor, DC level drift error induced by temperature influence will affect the measuring accuracy of the system.
本文归纳给出多维系统测量误差分析计算方法措施,并给出算例。
This text induced Multi - Direction System measure - error - analysis calculation method and measure, and calculation examples.
最后还进行了整个系统测量误差的分析。
误差分析表明:在传感测量系统无平移系统误差时,与传统标定方法相比,该方法的补偿精度略有下降。
The error analysis shows that the compensated precision is slightly lower than the traditional calibration method, when there isn't transferring system error in the measuring system.
当在传感测量中加入平移系统误差时,该方法的补偿精度不变,而传统标定方法的测量精度明显下降。
But compensated precision isn't changing, when there is transferring system erros the measuring precision of the traditional calibration method is apparently descension.
本文拟通过动态测试数据处理来分离测量结果、系统误差和随机误差。
In this paper dynamic measurement data processing is used to separate the results of measurement, systematic error and the random error.
本文通过动态测试数据处理来分离测量结果、系统误差和随机误差。
This paper discusses a method to separate -measurement result from systematic error and random error by processing dynamic measurement data.
当传感器存在刻度系数误差、安装误差和测量偏差时,将会明显降低系统的FDI性能。
However, the sensor errors such as input axis misalignment, scale factor errors and biases, have significant effect on the FDI performance.
同时,对系统的测量误差进行了讨论。
At the same time, the system measurement errors were analysed.
因此,对于非正交坐标系测量系统的误差研究变得非常有意义。
As a result the research on the system 's error is of great meaning.
由于光栅干涉测量系统以光栅栅距作为测量基准,相对于传统干涉仪,光栅尺系统受环境因素造成的测量误差影响较小。
Because the measurement standard of grating system is grating pitch, compared to usual interferometer, diffractive grating, system reduces environment influence on measurement accuracy.
实验研究了中子倍增率测量的系统误差。
Systematic errors in measurement of neutron multiplication have been experimentally studied.
介绍了微机控制的阶梯轴多参数在线测量系统的测量原理、系统构成及测量误差分析。
The measuring principle, system composition and measuring error analysis of the computer controlled step shaft multi parameters on line measuring system are introduced.
试验结果表明:采用该方法进行温度补偿后,可以基本消除流体温度变化引起的测量误差,提高系统的测量精度。
The result of experiment shows that the measurement error from fluid temperature changes can be almost removed, and the accuracy for this system can be improved.
在考虑不同误差属性的基础上,给出了脱靶量测量误差在伺服控制系统中的传递方法。
Based on the attributes of different errors, the method for transferring miss distance measurement error in servo control system is given.
相位失配误差是声强测量系统的主要误差源,仅靠提高仪器的精度很难消除这一误差。
The phase mismatch error is the main error source of sound intensity measurement system. It is difficult to eliminate this error only by upgrading the accuracy of instrument.
根据双水听器测量声强法原理进行了误差分析,提出了该双水听器声强测量系统的校准方法。
According to the principle of two-hydrophone method for intensity measurement, the error analysis is done.
文章通过对测量系统及其不确定度的研究,分别基于测量系统分析和误差溯源对测量系统进行了不确定度评定和精度保证。
The paper studies the measurement system and uncertainty. Based on the analysis of system and the source of error, the paper does the uncertainty evaluation and accuracy undertaking.
应用推荐