本文介绍模拟试验中轴承表面光洁度和配合间隙与磨损的关系，同时简述了磨损试验和测量方法。
This paper investigates the influence of bearing's surface finish and clearance on its wearability obtained by simulating tests. The method of the wear test and measurement are briefly described.
光纤。第1 - 45部分：测量方法和试验规程。模场直径。
Optical fibres - Part 1-45: measurement methods and test procedures - Mode field diameter.
光学纤维。第1 - 53部分：测量方法和试验程序。水浸渍。
Optical fibres - Part 1-53: measurement methods and test procedures - Water immersion.
光学纤维。第1-21部分：测量方法和试验程序。涂层几何形状。
Optical fibres - Part 1-21 : measurement methods and test procedures - Coating geometry.
本文介绍了在风洞光学测压试验中应用虚拟仪器技术对模型表面温度和模型表面光照强度的测量方法。
The paper describes the measurement method for model surface temperature and model surface illumination strength in wind tunnel optical pressure measurement test by the virtual instruments.
介绍了型式认可试验和工厂例行检验中有关信息技术设备的保护连接导体电阻的测量方法，以及在某些特殊设备上的应用。
The text introduced the test method and application in some special instances about Information technology equipment Protective Bonding Conductor in Type test and Routing test.
结合对数放大器自身的特性，介绍了此电路在BPM系统中的组成，工作原理，试验结果和参数的测量方法。
According to log amplifier's characters, we introduce the structure, principal, experiment results and measurement of the parameters of the circuit in BPM.
目的 研究最大横径和横竖平均径两种不同测量方法对皮内结素试验反应结果的影响。
Objective To evaluate that the measures of the largest transverse diameter and ofaverage diameter affect the results of Mantoux test.
分别采用有限元分析和试验标定法对支撑鼓泡塔的悬挂系统进行检测，结果表明微位移的测量方法准确、可行。
The Finite Element Analysis and experiment method were applied respectively to validate the veracity of the micro-displacement method. And the results show that this measurement method is feasible.
研究利用矢量水听器测量水下目标低频辐射噪声的问题，并给出了测量方法和海上试验结果。
Studies the measurement of low frequency radiation noise from an underwater target by a vector hydrophone, discusses the method of measurement and presents the test results in the sea.
介绍了燃油均匀分配性的概念和定义、测量方法及试验设备的构成。
The conception and definition of fuel uniform distribution, test method and structure of test equipment are present.
针对直升机操纵系统间隙难以精确测量的问题，提出了一种直升机操纵系统间隙测量的新方法，并对此测量方法的理论依据、试验过程和结果进行了分析。
A new way to measure the gap in helicopter control system is introduced, and the theoretical basis, test process and result of the measurement are discussed.
传统复合地基试验测量方法是利用压力传感器对复合地基直接进行测量，存在试验费用和精度等问题。
Pressure sensors were directly used in the traditional measurement methods for composite foundation. The problems of cost and precision might be aroused.
并介绍了一种便捷的测量方法，该方法可在进行扬声器寿命试验的过程中同时测量阻抗和温度。
A convenient method is presented, which can be applied to measure impedance and temperature during the life test of loudspeaker.
在试验结果的获取中，为能够得到很难测量的线电极周围的放电间隙和工件形状数据，提出一种新的三维形状测量方法。
In order to obtain the 3D data of the discharge gap and workpiece shape from the experimental results, a new measurement is proposed.
该方法在空间交会对接地面仿真系统的视觉测量子系统中进行了试验，现场实验结果验证了本文视觉位姿测量方法的可行性和有效性。
This method has been successfully applied to the space rendezvous and docking simulation system as visual measurement subsystem, the experiment results validate the feasibility of the proposed method.
并进行了复合材料板拉伸试验，复合材料平板实验计算结果和应变电测法得到的结果进行了对比，实验表明两种测量方法得到的结果相吻合。
The method was also used to measure strain in the tensile test of a composite laminate plate. The results agree fairly well with those obtained by the conventional measurement.
并进行了复合材料板拉伸试验，复合材料平板实验计算结果和应变电测法得到的结果进行了对比，实验表明两种测量方法得到的结果相吻合。
The method was also used to measure strain in the tensile test of a composite laminate plate. The results agree fairly well with those obtained by the conventional measurement.
应用推荐