4缸机为16气门DOHC（双凸轮抽）设计，配备丰田VVT-i（智能正时可变气门控制系统），最大功率179hp/6000rpm(131kw/6000rpm),最大扭矩172lb-ft/4000rpm(233Nm/4000rpm).
The 4-cylinder is a 16-valve DOHC design with Toyota’s VVT-i variable cam timing system, and is rated at 179 horsepower at 6000 rpm and 172 lb-ft of torque at 4000 rpm.
输送皂角泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.
当设计螺杆泵转子的齿形时，需要计算它们的液压扭矩。
It is necessary to compute the screw hydrostatic torque in designing the teeth profiles of screw pumps.
提出了定扭矩螺栓强度设计方法。
针对水轮机主轴扭矩检测系统中的光栅扭矩传感器，设计了一种新型电路。
A new circuit used for the grating torque sensor of hydraulic turbine's principal axis system is designed.
传动扭矩是矫直机主传动系统设计的主要依据。
The design of the main drive system mainly bases on the torque moment of transmission shaft.
采用专业轴承设计结构，实现高负载，高扭矩和高刚性。
High loading capacity, hight torque and high rigidity achieved by adapting professional bearing design structure.
简要介绍了设计的395DB离合器的结构特点，并对该离合器的传递扭矩、温升、滑磨功、踏板力进行了校核。
The structural features of the developed 395DB clutch are briefly introduced, and the clutch′s torque capacity, temperature rise, slipping work and pedal force are reviewed.
苏格兰枷锁其设计特别适合高阀门开始或结束的扭矩要求。
Its scotch yoke design is particularly suited for valves with high start or end torque requirements.
这就要求设计概念，提供热增长的灵活性，同时反应，大扭矩，分离负荷和外部管道负荷。
This requires design concepts that provide thermal growth flexibility while reacting large torques, separating loads and external ducting loads.
紧凑和高效的设计产量高扭矩，即使在低压力。
The compact and efficient design yields high torques even at low pressures.
在设计承受扭矩和弯曲的轴类件时，一定要从本企业的实际情况出发，来实现材料的仿应力强化。
In the design of axles bearing moment of torsion and bending, it is necessary reinforce stress of materials according to the real conditions of the enterprises.
利用模糊逻辑控制技术，设计了并联混合动力汽车的模糊逻辑扭矩控制策略。
Applying fuzzy logic control technology to design fuzzy logic torque control strategy of the parallel hybrid electric vehicle.
倾斜枷锁开始设计提供高扭矩。
在设计阀门系统时，必须考虑水动力扭矩，这样有助于正确选择所需阀门产品。
When designing valve systems, hydrodynamic torque must be considered to help assure correct selection for the application.
广州地铁地质条件复杂，推力、扭矩大小的设计对能否顺利掘进很关键。
It is the key for propitiousness driving, designing thrust and torque, because the geology condition is complicated in Guangzhou.
为液压扭矩扳手执行机构的设计提供了理论依据。
The theoretic foundation is offered to the design of executing mechanism of hydraulic torque wrench.
同时，提出了数字式无线信号传输的设计方案，可以解决旋转系统扭矩测量的信号传输问题。
At the same time, we designed the wireless transmission scheme for digital signal transmitting, and solved the transmission problem of the torque measurement in rotating systems.
提出定扭矩攻丝机的设计原则，阐述了工作原理，通过自制攻丝机试验证实了该结构的可靠性。
It is pointed that design principle and processing principium for stable twisting moment tapping machine. And reliability of the construct is confirmed through testing of self made tapping machine.
提出了用圆筒两端加制法兰与端盖平面接触轴向螺栓连接的方法设计大扭矩磁滑轮的方案。
The new scheme is put forward to design magnetic pulley with large torsional moment by means of planar contact between end-cover and added flange fixed axially by stud bolt.
介绍了一种利用低速定扭矩气动扳手配置专门滚压夹头的新型密封条滚压装置的设计与应用。
This paper describes the design and application of a new type of weatherstrip rolling device where low-velocity, fixed-torque aerodynamic spanner and special roller head is employed.
给出了雷达的结构总体设计方案，计算了天线的惯性载荷以及风载荷，并由此得出方位转动电机所需的最小输出扭矩。
The paper presents the scheme of structural design of this radar and makes selection of stepping motor via the counting of wind load and inertia load of antenna.
合理的节曲线设计是可用于低速大扭矩液压马达的变中心距非圆行星齿轮机构正常工作的关键。
Appropriate pitch curve designing is a key of regularly working for non-circular planetary gear mechanism with variable center distance which can be used in low speed high torque hydraulic motor.
应用第四强度理论，求解杆柱在扭矩和轴向力条件下的复合应力，设计抽油杆柱。
Rod strings are designed by computing compound stress with the fourth strength energy on the condition of torque and axial force.
提出了高扭矩抛物线齿同步带轮滚刀齿形的设计方法。
This paper puts forward a design method of pulley hob with parabolic tooth shape, which is used in the high torque drive.
为了提高发动机的效率和扭矩、改善发动机的性能，针对CA4GE发动机研究、设计、开发了发动机塑料进气歧管。
In order to improve engine efficiency and torque as well as the engine performance, plastic intake manifold was developed for CA4GE engine.
介绍了一种履带车辆随车扭矩测试系统的工作原理、方案设计和试验结果。
The operating principle, schematic design and experimental investigation of an on board torque measurement system for a tracked vehicle are introduced.
双球轴承作为扭矩支持灵活的春天系绳设计。
Double ball bearing design with flexible spring tether as a torque support.
结果表明，在试验设计的加工温度和物料含水量范围内，加工温度和物料含水量对螺杆扭矩、第4区压力、第5区压力、产品膨化率和含水量都有极显著影响。
Within the designed range, the temperature and material moisture influences on the torque, the 4th zone pressure, the 5th zone pressure, the expansion rate, and the product moisture are significant.
结果表明，在试验设计的加工温度和物料含水量范围内，加工温度和物料含水量对螺杆扭矩、第4区压力、第5区压力、产品膨化率和含水量都有极显著影响。
Within the designed range, the temperature and material moisture influences on the torque, the 4th zone pressure, the 5th zone pressure, the expansion rate, and the product moisture are significant.
应用推荐