• 根据闭环系统灵敏度函数最大,从频域角度设计滤波时间常数保证系统具有一定的棒性。

    According to the maximum magnitude of the complementary sensitivity function, the filter time constant is calculated to assure the robustness of system.

    youdao

  • 破坏形式及其破坏进程控制机理了解把握保证工程设计估计准确性重要前提

    The understanding and hold of the failure of ice and its dominating mechanisms are important ininsuring the accuracy of the estimation of ice force in engineering.

    youdao

  • 改造吸收出口CO2体积分数基本在设计附近保证生产正常运行

    After the reform, CO2 content of exit gas of absorber come near design value, and so normal run of production is ensured.

    youdao

  • 文中采用牛顿迭代通过对牛顿迭代初始优化法器的优化设计保证计算精度的前提下有效地降低了求模运算量应用于实际雷达系统中。

    In this paper, the calculations are decreased efficiently and the result has the same precision in calculation by optimizing the initial number of Newton method and design of divider.

    youdao

  • 目的打造一种平衡并且设计任何面象对象系统时,保证参考度量防止任何有太高RF C

    The goal is to strike a balance and, when you design any oo system, to keep an eye on this metric and stop any class reaching too high a RFC value.

    youdao

  • 设计可以根据电网电压波动调整动作从而保证电缆绝缘电阻动作不变;

    The operating value of earth leakage protection can be changed with the mains voltage, but the operating value of cables insulation resistance is held the line.

    youdao

  • 并比较分析现场实测理论计算。检测结果表明索力满足设计要求保证结构安全使用

    The field measured values are compared with theoretical values, and the results show that cable force can satisfy the requirements of design, which may ensure the safety and use of the structure.

    youdao

  • 盲孔多孔砌体通缝强度低于规范计算,为保证结构安全,建议设计乘以系数0.9;

    The shearing strength of back covered porous brick masonry is slightly lower than the Standard level. A coefficient of 0.9 can be multiplied to ensure the safety of structures.

    youdao

  • 产量质量指标达到设计意味着利的技术保证浇铸管理简便,可在每个工艺阶段对连铸机进行全面控制。

    Production and quality index of round blooms are close to unit values, and this means that all Danieli technology guarantees a simple management of bloom casting that allows full con...

    youdao

  • 为了保证设计安全,分析时采用弹性支座固定支座形式,分别进行了特征以及整体稳定分析。

    The design of the shell with two bearings which were fixed hinge bearing and flexible hinge bearing was introduced. The process of the stability analysis and the eigenvalue analysis were given.

    youdao

  • 为了保证设计安全,分析时采用弹性支座固定支座形式,分别进行了特征以及整体稳定分析。

    The design of the shell with two bearings which were fixed hinge bearing and flexible hinge bearing was introduced. The process of the stability analysis and the eigenvalue analysis were given.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定