所述写入方法采用反馈信号与设定信号对比的写入的方法。
The writing method is the method for writing by comparing a feedback signal with a set signal.
本文阐述了电压闪变信号发生的基本原理,探讨了发生器实发信号与设定信号之间的关系。
In this paper, the basic principle of generating voltage flicker signal is described and the relationship between the actual generated signal and the given signal is discussed.
控制器的设计是以线性伺服控制理论为基础的,它不仅能够消除由于轨道倾斜所带来的扰动,也能使系统跟踪其设定信号,使小车稳定在参考位置上。
The control law includes the integration term which not only eliminates the constant disturbance due to the inclined rail but also assures the cart of following the given reference position.
l利用事件——当异步调用完成时设定的信号。
Using events - a signal is set as soon as the asynchronous call is finished.
开始密匙交换时,鲍勃要给爱丽丝发射两道强激光信号,之间的间隔是经过精密设定的。
To start the key exchange, Bob sends Alice two strong laser pulses separated by a precise interval.
每天的报警提醒有关使用一个在您所设定的时间声信号经常性的事件。
The daily alarm reminds you about recurring events with an acoustic signal at the time you have set.
第二步是设定行为信号和提示,防止自己寻求表扬。
The second is setting up behavioral cues and reminders to stop you from seeking praise.
本文介绍车速里程表的工作原理、信号取向和标度盘的设定,给出了车速里程表速比的计算方法。
Its working principle, the signal tropism and the setting of indexing plate are introduced here with the calculating method of its speed ratio.
同时结合凸轮轴位置传感器的信号进行判缸,并设定合理的基本诊断策略。
A basic diagnosis strategy is set and also the signal of the camshaft position sensor is used to judge the cylinder which misfire occurs.
同步控制器采用可编程器件,所有信号的时间关系均由软件设定,以计数方式产生。
The synchro controller utilized the programmable chip. Thus the time relationship among all signals were set up by software and generated in the mode of count.
讨论了有关的测试技术问题,特别对仪器动态测试稳定性问题进行了讨论,还对直接影响信号真实度的采样窗口设定问题进行了讨论。
The related technical problems, the dynamic measuring stability of the instrument and the setting of the sampling window directly effecting the signal trueness are discussed.
当信号从原中心频率偏移,信号越来越从设定的发射通道偏移,功率分析仪的功率电平会越来越低。
As the signal is shifted from the original center frequency, the RF power analyzer reads lower and lower power levels as more and more of the signal shifts out of the intended transmission channel.
扫描采样率对成像质量至关重要,可通过驱动信号的频率选择和图像采集时间的设定来控制。
The scanning sampling density crucial to imaging quality can be deliberately controlled by setting of the driving frequencies as well as fetching duration.
利用温度传感器测到被控对象的温度信号与设定温度值进行PID调节,从而控制高频输出功率的大小。
Temperature sensor will be used to measure the temperature signal and build temperature for PID adjusting to realize the automatic output high frequency power.
更短的设定通常切掉更多高点和低点并增加错误信号。
Shorter settings tended to carve out more peaks and valleys, adding false signals to the mix.
更长的设定则产生更少的信号,但是准确性不变。
Longer Settings produced fewer signals, but with equal accuracy.
该产品设定为检测不到信号时会在8秒后自动关机。
The product is automatically powered off when no signal is detected longer than 8 seconds.
当计时器超过设定的时间后,无线网络可以检测是否还停有汽车(通过回复信号),并报告警察汽车停车超时。
When a meter expires, it could check for the presence of a car (by bouncing a signal off it) and report the expiration to the police.
用户可以设定测量信号的直流偏压,测量振幅,脉冲宽度。
User may specify the DC bias, measurement amplitude, and pulse width of the measurement signal.
通过该设定,调制信号的调制宽度减小。
This setting decreases the modulation width of the modulation signal.
只要预先设定好胶合电流值和时间,本系统会根据电流的反馈信号自动调节,胶合电流不会受到厚薄的变化和模具温度上升的影响。
As long as the pre-set current value and a good bonding time, the system based on current feedback signal auto - Regulation, will not be glued current thickness change and mold temperature rise.
治疗枕装置由微处理器根据传感器信号控制压力模块,按设定程序对各气囊充或放气。
The treating apparatus has microprocessor to control the pressure modules based on sensor signals and inflates and deflates the air bags according to the set program.
可程控基准电压源不仅要满足传统基准电压源的所有性能指标要求,其输出电压还可通过外部数字信号来精确设定。
Except for traditional circuit requirements, programmable voltage reference requires that its voltage can be preset and regulated accurately through external digital signals.
被合成的频率扫描信号的起始频率、终止频率和扫描时间可根据需要随意设定,并且可以实现对三者的精确控制。
Start frequency, stop frequency and sweep time of the signal synthesized by the method can be preset freely and controlled accurately.
针对单点测试,可灵活地根据被测信号和应用环境的特殊要求来设定参数并有效记录存储数据。
During single test, the system can flexibly set parameters and effectively record data with the special requirement of the present environment and the tested signal.
一控制装置可输入一设定值,并将前述流量信号与该设定值比较,而产生出一控制信号,借以根据该控制信号控制警示装置。
The control device can input a setting value, and compares the flow signals with the setting value to generate a control signal, so a warning device is controlled according to the control signal.
一控制装置可输入一设定值,并将前述流量信号与该设定值比较,而产生出一控制信号,借以根据该控制信号控制警示装置。
The control device can input a setting value, and compares the flow signals with the setting value to generate a control signal, so a warning device is controlled according to the control signal.
应用推荐