为给船体下水提供水动力参数，采用计算流体动力学（CFD）方法对船体从船台上纵向重力式下水过程进行动力学分析。
To supply hydrodynamic parameters for ship launching, computational fluid dynamics(CFD) method was used to analyze the process of longitudinal gravity launching for ship from a slipway.
我们利用计算流体动力学的方法，分析了定常流与脉动流两种条件下，支架植入引起的血管壁面剪应力的变化。
We used computational fluid dynamics(CFD) to investigate the steady and pulsatile flows in the vicinity of model stents and focused on the changes of wall shear stress caused by the implanted stents.
以膏体充填力学参数为基础，运用ANSYS软件中的FLOTRANCFD计算流体动力学分析模块对膏体管道输送进行了数值模拟分析。
Numerical simulation analysis is made of the paste piping transportation using FLOTRAN CFD calculation hydrodynamic analysis module in ANSYS software based on the paste filling mechanical parameters.
连续使用收集的数据建模dcim和工程分析工具，如计算流体动力学(CFD)。
Continuous modeling USES the data collected by DCIM and engineering analysis tools such as computational fluid dynamics (CFD).
根据流体动力学理论分析了颗粒径与流化速度的关系，通过利用或建立简单的传热与燃烧模型，定量计算了不同粒径无烟煤颗粒的燃尽时间和一次通过炉膛时的停留时间。
With using some simplified heat-transfer & combustion model, the burn-out time and the stay-time(one times through furnace) of a single coal particle in the furnace of CFB were also calculated.
本文采用一多功能流体动力学计算软件，详细计算分析了NASA低速离心压气机叶轮内部的三维速度场。
Based on a multifunctional CFD software, the three-dimensional velocity field within the impeller of NASA low-speed centrifugal compressor is computed in detail in this paper.
王福军。计算流体动力学分析—CFD软件原理与应用[M]。北京：清华大学出版社，2005。
WANG Fujun. Computational Fluid Dynamics Analysis-Theory and Application of CFD Software [m]. Beijing: Tsinghua University Press, 2005.
应用计算流体动力学软件FLUENT，对QD128航改燃气轮机燃烧室进行了三维数值模拟计算分析。
The 3D numerical simulation of the QD128 aero-derivative gas turbine combustor was performed by using computational fluid dynamics(CFD) software FLUENT.
泵的三维模型不但可以用于零件装配、干涉检查、加工模拟，而且可以为有限元分析(FEA)和计算流体动力学(CFD)分析提供计算模型。
The 3-d pump model cannot only be used in assembly, intervene inspection and process simulation, but also provide computational model for FEA and CFD.
针对两栖车辆水上行驶流场研究需求，基于计算流体动力学，对静水条件下两栖车辆的水上行驶流场进行了仿真分析。
In order to evaluate the performance of wheeled amphibious vehicle during its design phase, numerical simulation was taken to simulate the amphibious vehicle's steering in the water.
针对两栖车辆水上行驶流场研究需求，基于计算流体动力学，对静水条件下两栖车辆的水上行驶流场进行了仿真分析。
In order to evaluate the performance of wheeled amphibious vehicle during its design phase, numerical simulation was taken to simulate the amphibious vehicle's steering in the water.
应用推荐