同时运用FLUENT计算流体力学模拟软件，模拟并优化了MAP反应器的结构。
At the same time, use FLUENT computational fluid dynamics simulation software to optimize the structure of MAP reactor.
本文利用计算流体力学CFD商业软件FLUENT对潜艇上使用的油气分离器内部流场进行了数值模拟。
This article does the research on the oil-air separator used in the submarine using FLUENT, the business software of CFD.
采用计算流体力学软件CFX4.4和CFX5.5对中国先进研究堆标准燃料组件流场进行了数值模拟。
Numerical simulation of the flow field of the standard fuel assembly in China Advanced Research Reactor is carried out by using computational fluid dynamics software CFX4.4 and CFX5.5.
根据计算流体力学理论对空化流场进行数值模拟，从理论上验证水力空化的发生效果。
Finally, numerical simulation based on computer fluid dynamic (CFD) has been made for verifying the effect of hydrodynamic cavitation theoretically.
基于经典波浪理论，以大型商业计算流体力学软件CFX为平台，可以实现数值造波及波物作用的模拟计算。
Based on the principle of wave, the simulation of wave generator and wave or wave-current forces on circular cylinder is presented by using CFX.
本文运用计算流体力学(CFD)技术对不同工况下的多热源置换通风房间内的温度场及流场进行了数值模拟。
Using the method of Computational Fluid Dynamics (CFD), the distributions of velocity and temperature in the room with displacement ventilation system with many heat sources have been simulated.
本文主要对EDI设备中的离子交换膜进行研究，并首次采用计算流体力学(CFD)软件对淡水室隔板的流场分布进行模拟。
In this paper, ion-exchange membrane used for EDI is studied, and flow field distribution modeling of dilute chamber with computational fluid dynamics (CFD) software is studied for the first time.
使用计算流体力学软件FLUENT，模拟均匀来流绕固定圆柱的流动，模拟雷诺数为20,40,100时的绕流流动，得到流场的流函数等值线图和速度矢量图。
Uniform flow around a mounting cylinder is simulated with the application of FLUENT software while Reynolds number is 20, 40,100. Stream function and velocity vector distributions are indicated.
应用计算流体力学软件CFX，采用多孔介质模型对中国先进研究堆(CARR)的堆芯流量分配进行了数值模拟。
Using CFX, the numerical simulation of the core flow distribution was performed for China Advanced Research Reactor (CARR) with the porous media model.
本文着眼于使用计算流体力学方法对带有竖直吸水管、正向进水的开敞式前池与进水池的流态进行数值模拟。
In this paper the open sump flow with vertical intake is simulated with calculation fluid dynamics method according to model-test reports of Lianhu pump station.
运用计算流体力学(CFD)方法，对V锥流量计进行了数值模拟，得到了锥体上的压力和速度的详细分布情况，并对其进行了分析。
The detailed distribution of pressure and velocity on the cone obtained after simulating the flow characteristics of a V-cone flowmeter with the computational fluid dynamics (CFD) method is analysed.
通过采用计算流体力学数学模型对催化转化器内流场的数值模拟，并与实验结果进行比较，验证了模型的准确性。
A computational fluid dynamics model was used to simulate the flow field of catalytic converter, and which was compared with the experimental results as to demonstrate the model validation.
本文将传统的螺旋桨动量理论与计算流体力学的方法相结合，数值模拟螺旋桨滑流对其后部件气动特性的影响。
This thesis concentrates on the application of CFD techniques to simulate the effect of turbo-propeller slipstream on the parts behind the propeller.
本文应用计算流体力学的理论和方法模拟了带内热源的三维空调房间室内气流的湍流流动。
This paper is an application of Computational Fluid Dynamics in the turbulent flow of a three-dimensional air-conditioned room in which there are heat sources.
对一个小的系统的计算已经表明在布朗动力学模拟过程中考虑流体力学相互作用的重要性。
Sample calculations on small systems illustrate the importance of including hydrodynamic interactions in Brownian dynamics simulation.
利用计算流体力学软件FLUENT-5，对带导流筒搅拌槽内的流场进行了数值模拟。
The commercial code of CFD (Computational Fluid Dynamics), FLUENT-5, has been used to numerically simulate the flow field in the draft-tube agitated tank.
以计算流体力学(CFD)为基础，采用有限容积法模拟计算了轿车车身的外部流场。
On the basis of computational fluid dynamics (CFD), adopting limited volume method, the external flow field of a car body is simulated.
应用计算流体力学(CFD)方法对转动坐标系下的三维环形密封流场进行了准稳态数值模拟，在此基础上进行了转子动力系数的计算。
Three dimensional annular seal flow field was simulated quasi-steadily with computational fluid dynamics (CFD) method in a rotating reference frame. The Rotordynamic coefficients were calculated.
本论文应用计算流体力学的理论和方法模拟三维较复杂条件下空调房间室内空气流场的湍流流动。
This paper is an application of Computational Fluid Dynamics in the turbulent flow of three-dimensional air-conditioned room.
运动界面的数值模拟是计算流体力学中的重要课题之一。
The numerical modeling of the moving interface is one of the most important problems in CFD.
利用计算流体力学软件对煤油在所设计的双模态超声速燃烧室内的超声速喷雾燃烧进行了数值模拟。
Numerical analysis of the kerosene spray supersonic combustion was carried out in the dual-mode supersonic combustor with the CFD software.
以现场数据为基础，利用计算流体力学软件FLUENT6.3为计算平台对焙烧炉进行了数值模拟研究。
Based on the field data, numerical simulation of the baking furnace is carried out using computational fluid dynamics software FLUENT6.3 for the computing platform.
采用FLUENT计算流体力学软件对糖化锅内的流场进行了模拟。
The inside field of the mash kettle is imitated with FLUENT software.
利用计算流体力学通用软件FLUENT对整体流场和定转子间隙区流场中周向流速度场进行了数值模拟，并对理论分析进行了补充。
The field of whole flow field and tangential velocity between stator and rotor were imitated based on FLUENT. The analysis in theory was replenished.
本文使用计算流体力学软件FLUENT对二维平面上转子对壁面液膜的刮擦过程进行模拟。
Thirdly, CFD software FLUENT was applied to simulate the wiping process by rotor on the evaporating wall in two-dimension plane.
应用计算流体力学软件FLUENT对旋风分离器进行三维气固两相流场的数值模拟。
The computational fluid dynamics software FLUENT is used to simulate the 3-d two-phase (gas-solid) flow of cyclone separator.
应用计算流体力学软件FLUENT，对固体火箭发动机喷管内的二维两相粘性湍流进行数值模拟。
A fully coupled two-phase viscid nozzle flow of SRM is numerically simulated with FLUENT software.
本文利用计算流体力学方法对空调器贯流风机系统内部气体流动进行了数值模拟；
In the text the internal flow of cross-flow fan is simulated with Computational Fluid Dynamics.
本文利用计算流体力学方法对空调器贯流风机系统内部气体流动进行了数值模拟；
In the text the internal flow of cross-flow fan is simulated with Computational Fluid Dynamics.
应用推荐