求在这种载荷下出现的角变形。
研究表明，T形接头的角变形沿焊缝长度方向是变化的。
Study showed that angle deformation of T joint is changed along the welded seam length.
对核电凝汽器制造中的大拼板多层焊后的角变形进行了计算机预测。
Angle distortion modeling and prediction with computer for heavy plate multi-pass welding are carried out during condenser fabrication for nuclear power station.
分析表明，适当选择三角变形因子，会使欧姆加热得到显著的增益。
Our analysis shows that it is possible to strengthen ohmic heating substantially by selecting suitable factors of the triangular...
分析表明，适当选择三角变形因子，会使欧姆加热得到显著的增益。
Our analysis shows that it is possible to strengthen ohmic heating substantially by selecting suitable factors of the...
分析表明，适当选择三角变形因子，会使欧姆加热得到显著的增益。
Our analysis shows that it is possible to strengthen ohmic heating substantially by sel…
结果A组27例较少发生内眦角变形、睑外翻，上下泪点复位良好。
Results Group A had less medial canthus malposition and less eversion of the eyelid.
角变形或其他几何缺陷的存在，造成膜应力和剪应力沿着器坒而变化。
The presence of angular distortion or other types of geometric defects causes the membrane stress and shear stress to vary along the wall.
运用固有应变法研究了六个固有应变分量分别对搭接接头焊接角变形的影响。
The effect of each inherent strain component on the angular distortion of the lap joint is studied using inherent strain method.
在此基础上，进一步提出了一种用于预测角焊缝角变形的线弹性简化方法，即剪切固有应变法。
Furthermore, a new simplified elastic method called as inherent shear strain method is developed for forecasting fillet weld's angular distortion.
本文阐述一般球罐焊接缺陷的有关断裂力学计算，介绍了由于角变形和错边量引起的附加弯曲应力。
This paper deals with the general calculation of fracture mechanics on the weld defects of a spherical tank. The additional bending stresses caused by both the angular distortion and the stagger toe.
以T形焊接接头为算例，结合热弹塑性有限元法和映射应变分量法，研究了角焊缝角变形的产生机制。
The conception of deformation angle of helix pre-former is introduced and process parameters are analyzed with math regression method.
压力容器特别是大型球罐，在组装焊接过程中极易产生错边及角变形缺陷，该缺陷的存在将在容器中产生严重的应力集中。
Welding butt joint and angular deformation are easy to take shape during the assembly welding of pressure vessels, especially giant spherical tanks.
利用温度与变形实时测量系统，对铝合金5a12薄板氩弧焊接动态角变形过程进行了试验研究，探讨通过特征值来描述角变形动态行为。
The characteristics of dynamic welding angular distortions of aluminum alloy 5a12 with tig welding are investigated by self-made welding dynamic temperature and distortion measuring system.
风成沙丘普遍存在角砾前积、拖曳褶皱和倒转褶皱等同沉积变形构造。
The synsedimentary deformation structures are common in eolian dunes, such as brecciated foresets, drag folds and overturned folds.
用实验方法研究了中碳钢两相组织在等通道角挤压过程中的强烈塑性变形行为和组织演化过程。
Severe plastic deforming behavior and microstructure evolution of two phases in medium-carbon steel during equal channel angular pressing (ECAP) were investigated by experimental method.
通过对观测资料的分析研究，获得了该区条件下高强度综放工作面开采时的地表移动变形规律、各种角值参数和预计参数。
By analyzing and studying the survey data, we have obtained ground movement and deformation rules and different kinds of Angle parameters as well as prediction parameters under the condition of.
分析了济钢干熄焦焦罐存在的角部开裂、框架横梁和吊耳拉杆变形的原因。
The reasons of corner crack and deformation of frame beam and ear draft of the coke pot of CDQ at Jigang are analyzed.
为了描述畸形河湾扭曲变形的程度，提出了河湾法向角的概念。
The paper puts forward the concept of normal Angle of winding bend for describing the degree of distortion and deformation of malformed winding bend.
变形由强烈的塑性变形到弱变形，变质由角闪岩相到低绿片岩相及低于低绿片岩相。
The deformation was changing from plastic intensity to weakness and the metamorphic facies ranged from amphibolite to low-grade greenschist.
结果表明：随着初始主应力方向角的增大，轴向残余变形由压缩状态的正值逐渐过渡到伸长状态的负值。
The results show that: with the initial principal stress direction angle increases, the axial residual deformation from the compression state gradually transits to the elongation.
用板壳大变形理论转动角计算方法，对阜新矿区王营井田煤层大变形断裂和破裂带进行分析和预测。
The method of plate and shall large deformation rotation analysis is used in Wangying coal mining district, Fuxin area to predict faults and fractures in coal seams.
对冷弯型钢的纵向变形过程进行了力学分析，得到了变形微分方程，求得了转动角的理论公式，并对其变形形状进行了分析计。
Through the mechanical analysis, the differential equation for the longitudinal deformation of cold forming steel is derived, and the formula for longitudinal rotation Angle is obtained.
给出了激光模式之间的耦合以及等效光束发散角与镜面变形量之间的关系。
The coupling among laser modes and the relations between equivalent beam spread Angle and the surface deformation of the mirrors are obtained.
对造成轧辊烧轴承的原因进行了分析，结果表明：轧辊烧轴承主要与轧辊送进角的变化，冷却水的水量、水压及水管位置，轧辊架变形情况等有关。
Result showed that main reasons on ablation of roll bearing were transformation of forward Angle, flow value of cool water, water pressure, water pipe position, and deformation of roll-shell et al.
采用“立方”孔型变形形式，结合简明的超越三角方程进行设计计算，以得到精确的孔型尺寸及高表面质量的焊管。
A precise pass-size and welded pipe with excellent surface quality can be get when the deformation way of cube-pass and design calculation with surpass trigonometric equation are used.
结果表明抱辊偏心对变形抗力有影响，辗扩工艺具有不完整的三角形速度场。
The results show that eccentricity of ring holder affects the deformation resistance that the velocity field is a non-perfect triangular one.
提出利用高精度测角仪测量齿轮副在啮合过程中不同啮合位置时轮齿受载综合变形的新方法。
In this paper, a new method to measure meshing composite deflections of loaded cylindrical involute helical gear by using high precision clinometer is presented.
然而传统的三角网控制方法已无法满足高精度的变形观测需要。
But the traditional trigonometric net control can not obtain high precise deformation observation.
介绍了典型的圆管变三角形及多边形型材的变形方法。
It introduces the change methods of typical round pipe changing into triangle and multi side pipe.
应用推荐