采用可达到要求厚度的浇铸参数。
因为中国的不锈钢不是结实的不锈钢，而是夹层结构。虽然按照要求厚度制成，但是用磁铁测试法就可以一探究竟。
Because stainless steel in China is NOT solid stainless steel it is a sandwich material. which is then rolled out to the required thickness but a quick magnet test will reveal all.
这减少了设备的厚度和电压损耗，从而降低材料的质量要求和探测器的材料成本。
This decreases the device thickness and depletion voltage and consequently reduces material quality requirements and cost of the detector material.
若冰层上方还存在一层固态气体层，如干冰——二氧化碳的固态形式，维持液态水存在的冰层厚度要求就能相对降低。
The ice cap could be thinner and still protect water if it were topped with a layer of frozen atmospheric gas, such as dry ice, which is solid carbon dioxide.
但此设计要求硅片厚度不超过5纳米(一米的十亿分之一)。
But the design requires that this silicon layer be no more than five nanometres (billionths of a metre) deep.
为了满足这些要求，连续油管制造商提供了更大范围的屈服强度，直径和井(壁)厚度，从他们的角度作出了回应。
To meet these requirement changes, the ct manufacturers-for their part-have responded by offering a greater range of yield strengths, diameters, and wall thicknesses.
如果日后由于材料刚度的需要要求改变材料厚度，可能导致要将阳模转换为阴模。
If the day after due to the stiffness of the material required to change the material thickness, may lead to male into female die.
在经过对大量的检测数据的分析后，隧道二次衬砌厚度的检测要求可采用数理统计方法表达。
After pass through analyze a lot of fact checking data, tunnel lining concrete thickness require could express by probability statistic.
玻璃传送厚度可根据有关加工玻璃工艺要求调节，加热温度可按需要事先设定。
Send thickness of the glass can be processed in accordance with the relevant requirements of glass conditioning, heating temperature may need to set in advance.
卖方应加以检查确认以保证买方建议的厚度在指定条件下达到强度要求。
Vendor shall check and confirm under his guarantee that such thickness provide the proper strength under the specified conditions.
对厚度较薄或要求外形尺寸严格的产品，返修时应采用砂轮打磨等方法，以防变形。
Grinding wheel method has to be taken to avoid deformation during rework for think thickness material or strict dimension requirement parts.
而定位格架的表面颜色、钎焊缝质量、外形尺寸、破断力和结合层厚度均达到钎焊技术要求。
The grids completely meet with the requirements for soldering on surface color , welds quality, overall dimension, rupture stress and joint thickness.
螺旋桨大会，根据要求3，其中每一层粘弹性材料是均匀的厚度。
A propeller assembly, according to claim 3, wherein each layer of viscoelastic material is of uniform thickness.
但油气的聚集和油气藏的形成，对源岩厚度有一定要求。
However, the hydrocarbon accumulation or reservoir formation requires some thickness of source rock.
台面采用不锈钢拉丝板，可按客户要求提供板材厚度以及颜色尺寸。
Tops stainless steel wire drawing board, according to customer requests for sheet thickness and the color dimensions.
加强钢带的厚度与宽度根据管材直径、环刚度要求不同而分别设计确定。
The thickness and breadth of the steel strip is determined according to different pipe diameter and ring stiffness class requirements.
侧墙卷材屋顶防水层的保护层与屋顶防水层应结合紧密、保护层厚度应吻合设计要求。
The protective layer of the side wall waterproof layer and waterproof layer should be closely combined, the thickness of the protective layer shall comply with the design requirements.
高温气冷堆对燃料微球各包覆层的厚度有严格的要求。
The thickness of coatings for the HTGR (high temperature gas cooled reactor) coated fuel particles must meet design requirements.
本文提出了最小水膜厚度应满足的基本要求。
This paper presents the basic demand that the minimal water film thickness must meet.
如果未达到要求的湿膜厚度，应覆涂直到满足指定的湿膜厚。
If the required paint film thickness has not been achieved, the additional coats should be applied till the specified thickness is attained.
并且随着埋藏深度的增加，要求作为仓储层的砂砾岩体厚度也随之增大。
With the burial depth increasing, the thickness of glutenite body as storage layer should be thicker.
为了满足汽缸垫稳定的压缩、回弹性能要求，应注意复合板的厚度公差和柔性石墨面材最佳的密度范围的控制。
In order to meet steady compression -resilience properties as cylinder gasket, the thickness tolerance of composite sheet and the density of flexible graphite plate should be control.
拉力依照厚度，以顾客要求为基础的宽度有。
Tension is given according to thickness, width based on customer requirement.
因此，对小孔直径、穿孔板厚度都有一定要求。
Therefore there are some demands set for the small hole diameter and thickness of the perforated plate.
厚度较薄：可灵活适应各种设备检修的要求，提高有效空间。
Thinner thickness: it can fit all kinds of Equipment repair and enhance effective space.
分析方法是半解析法，没有应力和位移模式的假设，不限制壳的厚度，不要求两壳间的连接弹簧或其它支撑弹簧均匀分布；
A semi-analytical method with no assumption of stress and displacement is developed, in which the thickness of shell is not restricted and the uniform distribution of springs is not needed.
并与实际屏蔽厚度进行了对比，得出了实际屏蔽厚度均符合辐射防护要求结论。
Reality shielding thickness accord with the demands of radiation protection by comparing with calculation result of shielding thickness.
但随板坯厚度(层数)的增加，即在制造厚度有特殊要求的产品时，应考虑采用分步热压法。
As the thickness of blank increases, when the special products was required in thickness, it may be thought of graded hot-pressing.
但随板坯厚度(层数)的增加，即在制造厚度有特殊要求的产品时，应考虑采用分步热压法。
As the thickness of blank increases, when the special products was required in thickness, it may be thought of graded hot-pressing.
应用推荐