通过对其疲劳性能的实验研究，发现裂纹扩展速率的大小及刚度的下降与加载的最大循环应力密切相关的规律。
The fatigue properties were researched and found that the crack propagation velocity and the decline of rigidity were related to the maximum cycle stress.
木文研究了间接直流电位法（IDC法）和交流电位法（AC法）用于监测疲劳短裂纹扩展速率的有关技术问题。
The technique of measurement of growth, rate of fatigue short crack with indirect KC (IDC) potential system and AC potential system was investigated.
本文采用断裂力学方法来估算结构构件的疲劳寿命，这其中主要围绕裂纹扩展速率表达式展开研究。
Fracture mechanics is adopted to estimate the fatigue life of structural members, and among the rest, crack growth rate formula is studied.
研究表明，大量规则分布、互不重叠的合金化区及其周围的相变硬化区从总体上降低了疲劳裂纹扩展速率，提高了材料的疲劳寿命。
It is shown that a regular pattern distribution of scattered alloying zones which surrounded by phase transformation zone can retard the fatigue crack growth rate and improve the fatigue life.
为适应大型工程机械焊接用钢需要，对低合金高强度钢HG80及其焊接接头的疲劳裂纹扩展速率进行了研究。
To meet the development of steels used for the large engineering machinery, fatigue crack growth rates of a high strength low alloy steel HG80 and welded joint were investigated.
应用二维单侧容限系数公式，提出了一种测定金属材料疲劳裂纹扩展速率的小样本方法。
A small sample method for testing fatigue crack growth rate curve of steel was presented in this paper using a formula of two-dimensional one-side tolerance factor.
熔合线和焊趾处疲劳裂纹扩展速率较其他部位大。
The fatigue crack propagation rate of the fusion line and weld toe are greater than that of the others.
结果表明：与纯低周载荷作用相比，高低周复合载荷下球墨铸铁的裂纹扩展速率明显加快，极大地降低材料的疲劳寿命。
The results show that the crack growth rate under high-low cycle complex fatigue load is greater than that under low cycle fatigue load, and so the fatigue life is obviously reduced.
疲劳裂纹扩展速率和CTOD测试型不锈钢304研究和焊缝金属的温度范围-162度到另一个房间 温度。
The fatigue crack growth rate and CTOD tests on type 304 stainless steel and weld metal were studied over the temperature range -162 degree C to room temperature.
根据试验测定的焊缝各区冲击韧性、断裂韧性、疲劳裂纹扩展速率和疲劳裂纹扩展门槛值，对焊缝力学性能作出综合评价。
The mechanical properties of the butt welded joints have been evaluated according to the impulsive and fracture toughness as well as the rate and threshold values of fatigue crack propagation.
本文用宏观和微观方法测量了几种高强度钢的疲劳裂纹扩展速率，用金相和断口复型法观察了疲劳断口的微观形态以及与显微组织的关系。
The studies were carried out of the test of fatigue crack growth rate and relative to the microscopic morphology of fracture surface in certain high-strength steels.
本文研究了SCT试样高应变区的疲劳裂纹闭合效应和疲劳裂纹扩展速率。
The fatigue crack closure and fatigue crack growth rate in the high strain region of SCT specimen are studied.
在此基础上，建立了腐蚀环境下疲劳裂纹扩展速率试验中裂纹长度的自动检测技术。
On the basis of this, an automatic measurement technique of fatigue crack length in fatigue crack growth rate test under corrosive circumstance is established.
通过疲劳损伤准则，导出疲劳裂纹稳定扩展速率的计算公式。
The formula of the fatigue crack propagation rate was directly derived from the fatigue damage criterion.
等轴组织具有较好的拉伸性能、低的断裂韧性和高的疲劳裂纹扩展速率；
The equiaxed structure has good tensile property, low fracture toughness and high fatigue crack propagation rate.
定义裂纹深度扩展速率发生转折时对应的疲劳荷载的次数为鱼鳞伤萌生寿命。
The times of fatigue loads at turn over point is defined as the initial life of corner fine .
通过算例，将疲劳裂纹扩展速率公式中的各个参量全部随机化，并预测构件在给定可靠度下的疲劳裂纹扩展寿命。
By an example, each parameters are randomized in the Paris formula, and the propagation life of fatigue of the structure is prognosticated on the presented reliability.
为确定热障涂层的残余应力、结合力、断裂韧性、疲劳裂纹扩展速率等性能和特性，需要知道其杨氏模量和泊松比。
To analyze the characteristics of TBCs such as residual stress, bond strength, fracture toughness, and crack propagation ratio, the Young's modulus and Poisson's ratio are important parameters.
结果表明，该近似表达式适用于A型腐蚀疲劳裂纹扩展速率的计算。
The given calculating example shows that the expression has a better applicability for the crack propagation rate of type A.
起始裂纹在硬区的软对硬力学性能非对称焊接接头，起始裂纹越靠近软区，疲劳裂纹扩展速率越慢；
For CH joint, when the initial crack is located in hard zone, the closer the initial crack is to the hard soft interface, the slower the fatigue crack growth rate is.
同时分析了材料刚度衰减对疲劳裂纹扩展速率和扩展长度的影响。
The impact of the material constant and the degradation of elastic modulus are analyzed.
结果表明，稀土能推迟裂纹萌生的时间，降低裂纹扩展速率，提高其冲击疲劳抗力。
The experimental results show that adding rare earth into cast semi steel can defer the time of forming fatigue crack, reduce the speed of crack propagating and increase the impact fatigue resistance.
该合金的疲劳裂纹扩展速率对退火温度不敏感。
The temperature of duplex annealing has little influence on fatigue crack propagation behavior.
结果表明，微量合金元素硼改变了裂纹扩展途径和扩展方式，从而降低了疲劳裂纹扩展速率。
Result show that the trace boron additive causes the changes in the mode of fatigue crack propagation and its route, so that crack growth rate of 40MnB is lowered.
在排除焊接残余应力导致的裂纹闭合效应后，焊缝及热影响区疲劳裂纹扩展速率与基材相当。
Moreover, the fatigue crack growth rates of the weld metal and heat affected zone are lower than those of the base metal. Having excluded the effect of welding residual tress...
拉伸超载能阻滞321不锈钢的疲劳裂纹扩展速率，样品断面有明显的周期性的裂纹偏折或分叉；
The retardation of tensile overload will reduce the 321SS crack growth speed for the furcation on the fracture section.
基于三维裂纹特征，本文提出了一种测量孔边角裂纹近门槛区疲劳裂纹扩展速率及门槛值的实验方法。
Based on the features of the three-dimensional crack, an experimental method was presented to measure the near-threshold fatigue crack growth rate and threshold of the corner crack at a hole.
结果表明，复合材料补片胶接修补能有效地提高裂纹板的破坏强度和刚度，降低裂纹板的疲劳裂纹扩展速率，提高其疲劳寿命。
The effectiveness of the repair scheme, including the tensile strength, the fatigue life and the crack progress during fatigue was investigated experimentally.
在排除焊接残余应力导致的裂纹闭合效应后，焊缝及热影响区疲劳裂纹扩展速率与基材相当。
Having excluded the effect of welding residual tresses on crack closure, fatigue crack growth rates of the welded join...
在排除焊接残余应力导致的裂纹闭合效应后，焊缝及热影响区疲劳裂纹扩展速率与基材相当。
Having excluded the effect of welding residual tresses on crack closure, fatigue crack growth rates of the welded join...
应用推荐