铸铁连杆衬套提供最大承重的支持。
The cast iron rod bushing provides maximum load bearing support.
小齿轮轴运行多孔青铜轴承衬套。
艉轴管前、后轴承与衬套直径测量。
Measuring diameter of fore and aft stern tube bearing and bushes.
他的衬套的打开发现被藏的珠宝。
衬套的作用是阻止金属的彼此碰撞。
The function of a bushing is to prevent metals from touching one another.
衬套与电缆芯线外的屏蔽层连为一体。
The lining and a shield layer outside a cable core line are connected as a whole.
自润滑连杆衬套的低摩擦系数平稳驱动。
Self-lubricating rod bushing with a low coefficient of friction for smooth actuation.
离合器踏板处的总泵衬套。
时间越长青铜连杆衬套提供最大承重的支持。
The longer bronze rod bushing provides a maximum load bearing support.
铸铁的时间越长连杆衬套提供最大承重的支持。
The longer cast iron rod bushing provides maximum load bearing support.
上紧叶片弹簧加压机直到衬套被拔出叶片弹簧。
Tighten leaf spring press until bushing is extracted from leaf spring.
每节机筒间、机筒与衬套间具有良好的互换性。
Between each knot of machine barrel, and between machine barrels and bushes is favorable exchangeability.
在阀门处于压力负载下，不需要拆卸轴环衬套。
暴露到恶劣的温度条件下，接触到涂层或装有衬套。
Exposed to elevated temperatures with some finishes intact or bushings installed.
熔融的玻璃液流过喷丝头以及熔炉底部的耐高温衬套。
The molten glass flows through orifices and temperature resistant bushings at the base of each furnace.
研究表明：高温熔损和高温氧化是衬套受蚀的主要原因。
The results shows that melting and oxidation are the main reason of corrosion at the high temperature.
上部和下部衬套符合流畅平稳轻松操作阀门的标准要求。
Upper and lower bushings are standard for smooth valve operation.
安装新衬套时，必须遵循本程序，否则驱动轴可能滞塞。
This procedure MUST be followed when installing a new bushing or seizure to shaft may occur.
这样，所有运动的发生之间的衬套和轴承-而不是对螺栓。
That way, all movement takes place between the bushing and bearing - instead of on the bolt.
遇此，可采用修主动轴或衬套的方法恢复其正常的配合间隙。
In this, can use repair drive shaft and bushing method to recover its normal fit clearance.
本文提出一种压力泵中电磁马达含外壳的衬套应力计算新方法。
In this article a new calculation technique for stresses in the bush sleeve (shell), strengthened by a case, pulled on it, in the electromotor of the pressurized pump is offered.
齿轮泵主动轴与衬套磨损后，其配合间隙增大，必将影响泵油量。
Pump drive shaft and bushing wear, the tolerance clearance increases, will affect oil pump.
用阀门的阀杆(5)对准适配器衬套或持论操作机构(3)镗孔。
Align adapter bushing or gear operator (3) bore with valve stem (5).
针对加工中心研制了主轴锥孔陶瓷衬套，使机床的性能得到改善。
Taper ceramic bushing for spindle is developed for machining center, so that the performance is improved.
在这样的环境下，服役于深井衬套的镍合金的脆性大大地增加了。
Under such situations, the brittleness of the nickel superalloys employed in deep-well linings tend to increase significantly.
锡青铜是矿井中作为罐笼罐耳内衬套的主要材料，使用时磨损严重。
The tin bronze is the main lining materials as tank cage and ear in mine, wears seriously in application.
衬套：在三个位置上配置轴支撑，有利于轴校直和执行机构的支撑。
Bushings: Furnishes shaft support at three locations for positive shaft alignment and actuator support.
衬套：在三个位置上配置轴支撑，有利于轴校直和执行机构的支撑。
Bushings: Furnishes shaft support at three locations for positive shaft alignment and actuator support.
应用推荐