该仪器属于非接触式，使用聚焦的激光光束与被测表面相互作用所反馈的信息来进行表面形貌参数的测量。
As an un-contacting system, it uses the feedback-information of the reaction of the focused laser beam and measured surface to measure the surface appearance parameters.
研究了试验参数对涂层界面结合强度的影响以及阳极氧化状态参数对钛基体表面形貌的影响；
The effect of the experimental parameters on the interfacial bonding strength was investigated, as well as the influences of the anodic oxidation state on the titanium substrate surface appearance.
研究结果表明，PAN基炭纤维的氧化特性与其石墨微晶参数和表面形貌密切相关。
The results of the research works show that oxidation behavior of PAN-based CF is related with its morphology and graphite crystallite parameter.
在此基础上，本文主要分析了工艺参数对稀土转化膜成膜厚度、表面形貌、耐蚀性的影响。
Based on this, the technological parameter to become film thickness, the superficial appearance to the rare earth transformation membrane, the corrosion resistance influence has been analyzed.
通过表面轮廓仪测量加工试件表面形貌，采用自行研制的表面形貌参数表征系统进行表面形貌统计参数计算。
By the means of surface profile equipment, the machined surface was measured and the statistical parameter of surface topography was calculated.
以镀层表面形貌和显微硬度为考核指标，采用正交试验法优选了脉冲镀银参数，采用优选的脉冲参数电镀与直流电镀的银镀层作了比较。
Acoording to the surface appearance and the microhardness of coating, the parameters of silver plating with pulse current are optimized by the orthorhombic experiment.
用大量的实践经验论述了加工出合格的表面形貌对珩磨头、设备工艺参数和珩磨油石条、珩磨介质对珩磨质量关键性的影响。
Much practice experience demonstrates that in order to get qualifiedmachining surface, the machine tool, process data, honing stone as well as honing oil are very critical.
通过AFM研究了试验参数对薄膜表面微观形貌的影响，并对其浸润性能以及摩擦学性能进行了研究。
The influence of experimental parameters upon the morphology of the target films has been studied by using AFM.
依据分形几何理论，结合不可压缩粘性流体层流流动理论，建立基于分形参数的金属垫片泄漏模型，该模型揭示了泄漏率与密封表面形貌之间的关系。
According to the fractal geometry theory and the non-compressed viscous fluid laminar flow theory, the leakage model of metallic gasket based on fractal parameter was established.
表面粗糙度是机械加工中描述表面微观形貌非常重要的一个参数，表面粗糙度测量技术是现代精密测试计量技术的一个重要组成部分。
Surface roughness is an important parameter to reflect the micro-geometry in machine process, and also an important part of modern precise measurement technique.
通过给定的磨损参数，并结合经验数据，给出可能产生的磨粒和磨损表面形貌图谱，为后面的故障诊断和磨粒分析奠定了基础。
Based on wear parameter and experience data, the imitated wear particle and surface images of components were given. These are very useful for the fault diagnosis and wear particle analysis.
介绍了一组测量分析表面形貌的仪器系统，并对系统的建立和参数选用做了详细说明。
A suitable combination of instruments used to measure and analyse the wear sur-face texture is introduced in this paper.
考察了工艺参数对薄膜质量的影响，对薄膜的表面形貌，薄膜的生长速率以及热处理与薄膜的成相及其电阻率的关系进行了观察和分析。
The effects of the technological parameters on the quality of the films were studied. The growth rate and surface morphology of the films with cycle times were characterized.
说明节理的抗剪强度与法向应力和节理表面形貌特征参数有关。
It is shown that the shear strength of joint is concerned with normal stress and weighted average of mean profile angles of joint surface.
本文分析了棕化工艺参数对微蚀速率、表面形貌 、表面微观粗糙度、结合力的影响 。
In the paper, effects of brown oxide process parameters on micro-etch rate, surface topography, surface roughness, binding strength were analyzed through the experiment.
本文分析了棕化工艺参数对微蚀速率、表面形貌 、表面微观粗糙度、结合力的影响 。
In the paper, effects of brown oxide process parameters on micro-etch rate, surface topography, surface roughness, binding strength were analyzed through the experiment.
应用推荐