一种新的电压凹陷检测及其补偿控制策略研究。
Research on a new method of voltage sag measure and voltage compensation strategies.
说明补偿控制策略与变频技术在节能中的应用；
Analyses the application of compensation control strategy and frequency conversion technology to energy saving.
串流流量控制阀、温度补偿控制或旁通流量控制。
Series flow control valve, temperature compensated or bypass flow control.
本文论述了用前馈补偿控制提高开环励磁系统稳定性问题。
This paper deals with the stability improvement of open-loop excitation system by using feedforward compensation control.
文章介绍了镗削加工误差的在线建模和预报补偿控制方法。
On-line modeling, forecasting and compensating way for machining error in boring are introduced.
主要介绍一种光刻机投影物镜温度补偿控制的原理及控制算法。
The principle and control algorithm of temperature compensation for Sub Micron projection lithography objectives are introduced.
本文讨论了由线性多变量子系统组成的互联系统的分散补偿控制；
The decentralized compensating control of an interconnected system consisting of several linear multivariable subsystems is investigated.
第三章主要讨论中性线谐波电流的检测和补偿控制策略两个方面。
Chapter three mostly discusses the detection of neutral harmonic current and control strategy in two ways.
其次，研究了控制器为事件驱动时网络控制系统的时延补偿控制。
Secondly, controller design of NCS for delay compensation is studied when the controller is clock-driven.
针对系统负载扰动的随机不可控性，提出了负载扰动补偿控制方法。
For the uncontrollability and randomness of load vibration, the load vibration compensation control is proposed.
本文作者运用经典控制论对切削过程的位置误差补偿控制进行了研究。
In this paper, author studies the position error-compensating control problem of cutting process by using the classical control theory.
研究了前馈补偿控制的数学模型和实施电路，并提供了参数设计实例。
The paper proposes the mathematical model and physical circuit of feedforward compensation control for this purpose and gives an example of its parameter design.
针对典型的动态迟滞特征模型，提出了一种新型的迟滞补偿控制方法。
A new compensating control method for a kind of typical dynamic hysteretic model is proposed.
车削误差实时补偿控制中的关键问题之一是如何有效克服控制信号的滞后。
One of the key problems in real time turning error compensation system is how to overcome the lag of control signal.
介绍了一种可提高非球曲面超精密加工机床的轮廓跟踪精度的误差补偿控制方法。
An error compensation control method which can improve contour tracing accuracy of aspherical surface ultraprecise machine is introduced.
本文应用前馈控制模型对压电陶瓷刀具的位置进行补偿控制，取得了满意的效果。
A pre feed controlling model is adopted making compensate control for the position of piezoelectric ceramic cutting tool. The result is satisfactory.
基于直接横摆力矩控制方法，设计了一种前馈—反馈补偿控制的车辆稳定性控制器。
Based on direct yaw moment control (DYC) method, the vehicle stability controller with a feedforward and feedback compensator is designed.
在此基础上，从工程应用的角度研究了几种适用于导引头伺服机构的补偿控制方法。
On the basis of the above works, several effective compensatation controlalgorithms are researched to improve the precision of the seeker servo mechanism fromthe aspect of the engineering application.
对几千瓦以下的单相有源功率因数补偿控制芯片很多，其中UC3854最具代表性。
Single phase active power factor compensation control clips below thousands watts are very popular, among which UC3854 is most typical.
为了进一步提高系统的动态性能，在非线性PI算法中加入了负载电流前馈补偿控制。
To improve further the dynamic characteristic, the non-linear PI arithmetic with the load-current forward compensating (LCFC) control is also improved.
本文介绍一种适用于中、小水泥厂生料制备过程计算机控制的静态偏差补偿控制算法。
This article presents a static bias compensation control algorism which is suitable for preparation of raw material in small and middle scale cements plants.
试验结果表明，应用该补偿控制方法，可对滚珠丝杠的磨削精度提高1-2个精度等级。
The result indicates that the precision can be improved 1-2 precision grade by using the compensation control method.
从控制理论的角度，间接给出了恒定照度下人工照明的补偿控制策略，以实现照明节能。
From the viewpoint of control theory, the artificial lighting control strategy was given indirectly under the condition of a given constant illuminance and it could realize the lighting energy saving.
根据实际作业情况与操作手册，开发了电路板的控制软件，补偿控制算法也由软件来实现。
The software of the circuit board and compensation algorithm is developed on the basis of the actual operating conditions and manuals.
应用光电编码器作为滚珠丝杠转角位置检测元件实现了半闭环补偿控制，提高了系统的精度。
The photoelectric encoder is used for measuring the angular position of rotating ballscrew. Semi closed loop compensation control is realized and system accuracy is improved.
将加工尺寸预测与工艺能力预测结合起来，提出对加工尺寸进行反馈补偿控制的原理和方法。
Combining the forecasting of machining dimension with that of process capability in a machining process, principle and method of feed-back compensative control is proposed in the paper.
作为应用举例，DLQR用于重载汽车前轮舵角补偿控制(FSAC)模型中确定控制输入。
As an instance, DLQR was applied in determining the control input in the front steering Angle compensation control (FSAC) model for heavy duty vehicles.
将R BF网络引入轧机中轧辊的偏心补偿系统中。给出了实现偏心补偿控制的系统结构框图。
The RBF network in rolling mill eccentricity compensation system is introduced, and the block diagram of eccentricity compensation is given.
对准控制采用阶梯步长逐步逼近算法，并且引入了机械手姿态调整后的补偿控制，以提高对准效率。
Furthermore, a stepwise approach with varying step lengths, and a compensation strategy following the manipulator's rotation are introduced in the IC mask alignment.
对准控制采用阶梯步长逐步逼近算法，并且引入了机械手姿态调整后的补偿控制，以提高对准效率。
Furthermore, a stepwise approach with varying step lengths, and a compensation strategy following the manipulator's rotation are introduced in the IC mask alignment.
应用推荐