采用高强度螺栓、螺母垫圈，必须符合《钢结构用高强度大六角螺栓、大六角螺母、垫圈技术条件》要求。
Use of high strength bolts, nuts washers must meet the "high-strength steel hexagon bolts, large hexagon nuts, washers and technical conditions" requirement.
重要的是要在最后一个螺母上安装一个防松垫圈，否则它会逐渐变松。
It's important to put a lock washer on that last nut, or it can work loose.
中国是世界上最大的螺丝钉、螺母、螺栓和垫圈生产商，而欧盟是这些商品的最大市场。
China is the world's biggest producer of screws, nuts, bolts and washers, while the EU is its biggest market.
每个活塞都要拆下来并且打磨，每个螺母和垫圈都要清洗或更换，并且一个都不能少。
Each piston disassembled and polished, each nut and washer cleaned or replaced, accounted for.
可能受到振动、波动载荷、冲击载荷或动力载荷的内部螺栓应加以保护防止松动。可采用双螺母、防松动垫圈、点焊等。
Internal bolts subject to vibration, fluctuating load, impact load or dynamic load shall be protected against loosening. Double nuts, unti-loose washers, tack welding, etc. shall be used.
从进气管道的锁手柄上拆下螺栓、垫圈和螺母。
Remove the screws, washers and nuts from the lock handles for the air inlet duct.
我们公司主要生产牙条，垫圈，还有螺母。
Our company Specially offer Threaded Rod and Flat Washer, also together with Nut.
用螺纹联接并起紧固作用的零件称为螺纹紧固件。常用的螺纹紧固件有螺栓、双头螺柱、螺钉、螺母、垫圈等。
Parts with threads used for joining and fastening are called screw fasteners. The most widely used components as screw fasteners are bolts, double screw bolts, screws, nuts, washers.
它由称套、锁紧螺母、锁紧垫圈组成。
注：如果出现少量的泄漏，则拆卸锁紧螺丝，然后锁住垫圈和阀盖，然后轻轻紧固填料压紧螺母。
NOTE: If minor leakage occurs, remove lock screw, lock washer and cap and lightly tighten packing gland nut.
钢结构用高强度大六角头螺栓，大六角螺母，垫圈技术条件。
Specification of high strength bolts with large hexagon head, large hexagon nuts, plain washers for steel structures.
垫圈放置在螺母一侧，不得装反。
目前企业可生产的紧固件产品种类包括各类螺栓、螺钉、螺柱、自锁螺钉、自锁螺母、铆钉、销、垫圈以及其他专用件和异型件，涉及300多个标准。
Our products include all kinds of fasteners, such as bolts, screws, studs, self-locking screws, self-locking nuts, rivets, pins and washers with more than 300 standards, and non-standard parts.
齿爪装配时一定要将螺母拧紧，并注意不要漏装弹簧垫圈。
Tooth claw assembling must tighten the nuts and note don't short-shipped spring washers.
松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。
Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem.
在扳手的平面上握住阀杆(27)并拆卸螺母(51)，锁紧垫圈(46)，隔膜板(60)和隔膜。
Hold stem (27) on wrench flats and remove nut (51), lock washer (46), diaphragm plate (60) and diaphragm.
筒体螺栓的紧固螺母和筒体外壁之间也采用橡胶垫圈密封。
A rubber gasket seal is used between a clamp nut of a barrel screw bolt and the outer wall of the barrel body of the utility model.
小尺寸轴承使用带锁紧垫圈的锁紧螺母大尺寸的轴承使用带锁紧卡箍的锁紧螺母。
Smaller sizes use a lock nut with a locking washer, larger sizes use a nut with locking clip.
现在我厂主要生产紧固件产品中的螺母、平垫圈类系列的产品。
Now my main production plant in fasteners products nut, plain washer series products.
不包括法兰，螺栓，螺母，垫圈和衬垫。
收集必要的安装工具：柱切割器、柱螺母、垫圈、放大镜、打字机改正液。
Gather the necessary installation tools: you will need a column cutter column nuts ferrules a magnifying loop and typewriter correction fluid.
收集必要的安装工具：柱切割器、柱螺母、垫圈、放大镜、打字机改正液。
Gather the necessary installation tools: you will need a column cutter, column nuts, ferrules, a magnifying loop, and typewriter correction fluid.
它通常包括以下十二类零件：螺栓、螺柱、螺钉、螺母、自攻螺钉、木螺钉、垫圈、挡圈、销、组合件和连接副、焊钉等。
Usually there are 12 categories which are bolt , stud, screw, nut , self tapping screw, wood screw, gasket, retainer ring, pin, composite member, bolting, and soldering lamp.
尼龙锁紧母、金属锁紧母、K帽、六角螺母、盖帽形、蝶形帽及各式垫圈、挡圈、销类等。
The mother of nylon lock, metal lock master, K cap, hex nut, cap-shaped, butterfly hats and all kinds of washers, retaining rings, pins and so on.
公司月生产能力为4000吨，主要生产各类德标（DIN）、英标（BS）、美标（ANSI）、日标（JIS）的螺栓、螺母、牙条、地脚栓及配套垫圈。
We mainly produce various types of bolts, hex nuts, thread rods, anchor bolts, and supporting washers in DIN, BS, ANSI and JIS with 4,000 tons of monthly productivity.
本公司主要经营螺钉，螺母，弹簧螺母，螺栓，垫圈，牙棒，金属膨胀螺丝，异型冲压件，非标件，五金工具等。
My company mainly manages the bolt, the nut, the spring nut, the bolt, the gasket, the tooth stick, the expansion of metal screw, the heterogeneous pressing part, non-tender, hardware tool and so on.
杆体上对应于每套压紧件中的托盘和螺母之间处均套装一个垫圈。
On the rod body, a washer is sheathed with the part which is corresponding to the part between the tray and the screw nut of each compressing piece.
螺栓选用优质合金钢，螺母、垫圈选用优质碳结钢，圆柱头焊钉选用ML 15al。
The bolts are made from excellent quality alloy steel, the nuts and washers are made from carbon steel, cheese head studs for stud welding are made from ML15AL.
主要生产大理石挂件，不锈钢冲压件，以及各种标准﹑规格﹑材质的平垫圈﹑弹簧垫圈﹑冲压件﹑螺栓﹑螺母等机械零部件。
We mainly produce the marble accessories, stainless steel stampings, and flat washers, spring washers, stampings, bolts, nuts and mechanical parts in all kinds of standard, specification and material.
主要生产大理石挂件，不锈钢冲压件，以及各种标准﹑规格﹑材质的平垫圈﹑弹簧垫圈﹑冲压件﹑螺栓﹑螺母等机械零部件。
We mainly produce the marble accessories, stainless steel stampings, and flat washers, spring washers, stampings, bolts, nuts and mechanical parts in all kinds of standard, specification and material.
应用推荐