这有个土豆，这是螺旋锥。
下面转动螺旋锥，从你们那侧看是顺时针。
I'm going to turn the corkscrew as seen from your side, clockwise.
螺旋锥齿轮误差修正试验研究。
Experimental study on the error correction of spiral bevel gear.
可以看到螺旋锥，钻入了土豆，这就是矢量的方向。
And you'll see that the corkscrew goes into the potato then, of the vector.
采用优化的方法设计了主减速器螺旋锥齿轮。
Optimization method was used in the design of the spiral bevel gear of the main reducer.
有了螺旋锥法，很快就能得出方向，通过运用右手螺旋法则。
But I immediately have the direction by using the corkscrew rule.
给出了斜航式法向圆弧螺旋锥齿轮的参数化建模方法。
The parametric modeling method for loxodrome normal circular-arc spiral bevel gear was presented.
法向圆弧螺旋锥齿轮传动是一种新的锥齿轮传动形式。
The normal arc spiral bevel gears is a new type of transmission pair.
该机床是螺旋锥齿轮单件生产和设备维修的较理想设备。
The machine tool is suitable for helical bevel gears production in single piece and also for maintainence work.
提出螺旋锥齿轮超声振动复合研磨的方法，介绍了其原理；
The method of ultrasonic vibration lapping on the spiral-bevels and hypoid gears was first presented.
刀倾半展成法是加工螺旋锥齿轮和准双曲面齿轮的有效方法。
The "Tool Pan Tilted method" is a high effect method to generate spiral-bevel gears and Hypoid gears.
我国对螺旋锥齿轮加工的研究仍集中在“格里森”机床方面。
Researchers still put their emphasis on studying Gleason machine tools in our country.
研究并推导出了克林·贝格螺旋锥齿轮副重迭系数的计算方法。
The calculation method about the overlap coefficient of Klingelnberg spiral bevel gear system is studied and derived.
研究了螺旋锥齿轮齿面综合研磨率、动态互研与研齿修形机理。
The material general removal rate and the dynamic mechanism of tooth surfaces modified and corrected mutually during lapping process of hypoid gears were firstly investigated.
如果你想使用。,螺旋锥法则,必须保证自己是,在用右手坐标系。
You must work... if you use the right-hand corkscrew rule make sure you work with the right-handed coordinate system.
该研究是国内首次对螺旋锥齿轮动态力研齿进行的理论分析研究。
The theoretical analysis research of spiral bevel gear lapping with dynamic force is carried out.
随着多层螺旋ct的出现，医用CT正在向着螺旋锥束ct转变。
With the development of spiral multi-slice CT, medical CT is in transition towards spiral cone-beam CT.
基于有限单元法分析了螺旋锥齿轮强度和刚度相关问题的计算方法。
The strength and stiffness of spiral bevel gear are analyzed based on the finite element method.
这些公司对外均进行技术保密，外界很难获得螺旋锥齿轮的加工技术。
They keep their technique secret and others hardly acquire the machining technology about spiral bevel gears.
建立了螺旋锥齿轮研齿过程的动力学模型，求出了动态研磨力的大小。
The dynamic model of the lapping was setup, and the dynamic lapping force was calculated.
结合机床调整参数、齿轮啮合原理，建立了螺旋锥齿轮齿面误差修正模型。
The error correction model of tooth surface was established by machine tool adjustment parameters and meshing principle.
在螺旋锥齿轮硬齿面精加工这一环节上，我国与发达国家的差距尤为明显。
There is an obvious disparity between our nation and other developed nations in the field of hard surface finish machining of the spiral bevel gear.
螺旋锥齿轮有无限的使用寿命，而且比单蜗轮齿轮要高出50%以上的效率。
Helical bevel gears have an infinite life, and are 50% more efficient than single worm gears.
通过分析锥齿轮的加工方法和齿轮啮合理论，建立了螺旋锥齿轮齿面数学模型。
A mathematical model of spiral bevel gear tooth surface was built by analyzing manufacture method and meshing theory.
螺旋锥齿轮啮合时产生的附加动载荷是螺旋锥齿轮传动产生振动、噪声的主要原因。
Additional dynamic load during Spiral bevel gear meshing is main cause of vibration and noise. Based on national standard.
螺旋锥齿轮的啮合接触冲击特性和动态接触性能的好坏严重影响其整机的工作性能。
The meshing contact-impact and contact performance of spiral bevel gears has a strong impact on the whole machine performance.
提出了超声研磨螺旋锥齿轮的理论与方法。 分析了超声研齿不灵敏性振动切削机理。
The paper presented the theory and method for the ultrasonic lapping of spiral-bevel and hypoid gears and analyzed its insensitive vibration cutting mechanism.
根据干涉结果对螺旋锥齿轮的切齿参数进行调节，直至得到比较满意的螺旋锥齿轮副。
According to the result of interference test, the cutting tooth parameter is adjusted till the satisfied spiral bevel gear pair was acquired.
基于空间曲面共轭原理，确定齿轮切齿矢量关系，建立了螺旋锥齿轮的齿面矢量方程。
Based on the conjugation theory of space curved surface, the vector relation of gear cutting is ensured. Tooth vector equation of bevel gear is established.
基于空间曲面共轭原理，确定齿轮切齿矢量关系，建立了螺旋锥齿轮的齿面矢量方程。
Based on the conjugation theory of space curved surface, the vector relation of gear cutting is ensured. Tooth vector equation of bevel gear is established.
应用推荐