随着薄板厚度的增加，振幅增大。
With the increasing of the thickness of thin plate, the amplitude increases.
它具有LCD的薄板厚度、CRT般快速的响应速度和较大的动态范围。
Its thickness is the same as the LCD, the speed on the response and the dynamic scope are close to the CRT.
初步分析了厚度对矩形薄板热屈曲临界应变值的影响。
The effect of the thin plate's thickness to thermal buckling problem is analyzed.
本文给出了正交各向异性变厚度圆薄板在均布载荷与集中载荷作用下大挠度问题的解。
The solutions of a large deflection problem of thin orthotropic circular plates with variable thickness under uniform pressure and under concentrated load are obtained in this paper.
本文研究了厚度按线性规律变化的圆薄板在中心集中力作用下的非线性弯曲问题。
Nonlinearly bending problems, of circular thin plates with linearly varying thickness under central concentrated load are discussed.
本文给出了正交各向异性变厚度周边简支圆薄板在均布载荷下大挠度问题的解。
The solution of large deflection problem of thin orthotropic circular plates with variable thickness under uniform pressure under simply supported boundary condition is obtained in this paper.
薄板坯的晶粒度的大致范围在4～5级，其中在厚度方向上薄板坯中心部位晶粒度比侧部小半个等级。
The grain size grade is about 4-5 class, and that during the thickness the central is less half a class than the lateral.
钣金件是指由厚度均一的金属薄板制作而成的构件。
该单元应用于薄板和中等厚度板分析均有较高的精度，计算效率高，可用于工程中具有复杂形状的薄板和中等厚度板结构的分析。
It is accuracy to deal with thin and moderately thick plate bending, and it is suitable for computing the plate bending problems with various shapes in practise.
据此，建立了中厚度-薄板非线性振动的增量有限元列式。
On such basis, an incremental finite element formulation for nonlinear vibration of moderately thick and thin plate is presented.
其中，上述穿孔机构800，是在冲头用金属模 具820和冲模用金属模具830之间的空隙G大于薄板状加工对象W 的厚度状态下实施穿孔的穿孔机构。
The punching mechanism (800) performs punching in a condition where a gap (G) between the punching die (820) and the dieing die (830) is greater than the thickness of the sheet-like object (W).
具体研究工作如下。（1）研究了轴向运动等厚度粘弹性矩形薄板的横向振动和稳定性问题。
The main research work is as follows. (1) The transverse vibration and stability of the axially moving uniform viscoelastic plate are investigated.
将厚度梯度准则与有限元方法相结合，可在已知薄板单拉性能参数的条件下计算获得其成形极限图。
By combining the "thickness gradient criterion" and FEM, the FLD of sheet metal can be calculated when the tensile properties is available.
该薄板是接合设置于该球头主体的开槽处，且其厚度界于0.1～0.5毫米。该抗压内板是位于该球头主 体中且胶合固定于该薄板内面。
The sheet is jointed and arranged at the slot of the ball head main body and has the thickness of 0.1-0.5mm.
合理匹配工艺参数能够实现0.85mm厚度薄板的对焊，并且获得形貌良好的焊缝。
Experimental results also indicate that selecting appropriate process parameters can realize the butt-weld for the 0.85 mm thick Invar sheets in good welding modality.
薄板旋切芯、锯屑、木丝、刨花等以及厚度等于或者小于6mm的木质材料除外。
The revolved cut cores from wood sheets, scobs, wood-wools, wood shavings, and the wood materials which are 6mm thick or less shall also be excluded.
薄板坯处理技术在考虑到板坯在长度，宽度，厚度的温度均衡，提供了出色的先决条件。
The CSP process offers excellent pre-conditions with respect to a homogeneous temperature distribution over the strip length, thickness and width.
薄板坯处理技术在考虑到板坯在长度，宽度，厚度的温度均衡，提供了出色的先决条件。
The CSP process offers excellent pre-conditions with respect to a homogeneous temperature distribution over the strip length, thickness and width.
应用推荐