一个节点基于所通信的状态，向调度传输的其他节点通信输出链路状态。
One node communicates an outbound link state to other nodes which schedule transmission based on the communicated state.
当openmosix必须与其他节点通信时，客户内核会去调用一些系统调用。
When openMosix has to communicate with other nodes, the guest kernel invokes several system calls.
无线传感器网络由于部署区域广泛、节点通信能力较弱，常采用分簇的网络拓扑结构。
Because of the broad deployment region and weak ability in communications of wireless sensor networks, it is often clustered.
您指定的主机名称或IP地址就是其他节点将用于与正在创建的节点通信的主机名称或 IP地址。
The host name or IP address that you specify is what other nodes will use to communicate with the node being created.
逻辑上能和其他簇内节点通信的节点都可以做网关，这些节点相对于簇首节点称为网关支配集。
The node that can logically communicate with the nodes in other clusters has the ability to be gateway, and the set of these nodes is defined as gateway dominating set relative to cluster-head.
当移动设备访问互联网海量资源时，它们必须配置唯一的IP地址，才通过网关与对应节点通信。
When some mobile devices need to get a lot of resources from the Internet, they must be configured a unique IP address, and maintain communications with the corresponding nodes through the gateway.
在两个节点都运行后，即可使用net_adm：ping测试一个节点能否与另一个节点通信(请参见清单5)。
With both nodes running, you can test if one node can communicate with the other using the net_adm: ping (see Listing 5).
该思想通过对传感器发射功率的控制，致力于实现对无线传感器网络的生命期的优化，以及对节点通信链路质量的提高。
Through doing control with transmission power in WSN, the idea makes every effort to realize optimize the WSN's lifetime, and to enhance the communication quality between nodes.
因为hadoop主节点使用SSH与从节点通信，所以应该在主节点和从节点之间建立经过身份验证的无密码的SSH连接。
Because the Hadoop master node communicates with slave nodes using SSH, you should set up an authenticated no-passphrase SSH connection between the master and slaves.
汽车总线仪表用两根数据通信线进行CAN节点通信，实现了汽车各电控单元之间的资源共享，其已经成为当今和未来一段时间内的主导技术。
The automobile BUS-IP use two wires to communicate with the other CAN node, realize the resource using in common among the ECU. It has become the dominant technology in the future time.
一个ActiveCluster实现。ActiveCluster是用于编写基于集群的应用程序(监视集群中的可用节点并同这些节点通信)的框架。
A provided implementation of ActiveCluster, a framework for writing cluster-based applications that monitors the available nodes in a cluster and communicates with them.
要使一个IP网络中的两个节点能够通信，那些IP地址必须在整个网络中是唯一的。
To enable communication between two nodes in an IP network, those IP addresses have to be unique among the whole network.
此模型依赖部署管理器与其托管节点之间的紧密耦合的可靠通信链路。
This model relies on tightly coupled reliable communication links between the deployment manager and its managed nodes.
每个逻辑节点都分配了一个通信端口。
Each of the logical nodes is allocated a communication port.
每个节点都通过代理与部署管理器通信。
Each node USES an agent to communicate with the deployment manager.
在这个错误场景中，节点之间的通信链发生故障，每个节点都认为自己是主节点。
In this error scenario, the communication link fails between the nodes, and both nodes believe that they are the primary node.
节点之间的通信也要通过网络。
只要正确配置了DNS服务，节点就应该能够毫无问题地通信。
As long as the DNS service is configured properly, the nodes should be able to communicate without any problems.
接下来，让两个节点相互通信。
Next, we will make the two nodes communicate with each other.
完成上述操作之后，就可以从OSx机器建立通信，通过调用nodes函数验证是否可以看到远程节点。
Once you do this setup communication from the OS X machine and verify you can see the remote node by calling the nodes function.
与以太网和传真机不同的是，XForms并非网络上任何两个节点间的正式通信协议。
Unlike Ethernet or a fax machine, XForms is not a formal communication protocol between any two nodes on a network.
计算节点间的通信在“计算”网络上进行，它是一个运行于eth0上的私有网络，如图1所示。
Communication between the compute nodes occurs on the "compute" network, which is a private network running on eth0, as shown in Figure 1.
作为根用户发出以下的preprpnode命令，让现有节点和新节点能够相互通信。
Issue the following preprpnode commands as a root user to allow communication between the existing nodes and the new node.
Kerberos协议允许在不安全的计算机网络上通信的计算机节点以一种安全的方式互相验证。
Kerberos protocol allows computer nodes communicating on a non-secure computer network to authenticate each other in a secure manner.
一旦安装了openMosix，集群中的节点就会开始通信，并且，集群通过优化资源分配，不断地根据工作负载 对自己进行调整。
Once openMosix is installed, the nodes in the cluster start communicating and the cluster continuously adapts itself to the workload by optimizing resource allocation.
因为要与外部数据库通信，必须假设需要在模式中的所有WebSphere节点中添加jdbc驱动程序。
Because you are communicating to an external database, you must assume the JDBC driver needs to be added to all WebSphere nodes in the pattern.
您将再次使用集群管理器Web服务，确保管理器与节点之间的通信，并测试节点之间的通信。
You'll revisit the cluster manager Web service, ensuring communication between the manager and the nodes and testing communication among the nodes.
在所有节点上发出preprpnode命令，从而使集群节点能够相互通信。
Issue the preprpnode command on all nodes to allow communication between the cluster nodes.
bcast指令表示节点将通过此接口彼此通信并执行ping操作。
Bcast is a directive that means the nodes will communicate and ping each other on this interface.
SV - 2系统通信描述为物理节点及其相关的通信基础构架建模。
SV-2 Systems communications Description Models physical nodes and their related communications infrastructure. Composite structure Diagram Deployment Diagram 6.
应用推荐