聚合物用量小，含水回升率相对较高，产量递减率也相对较大；
The less polymer volume is applied, the higher water cut increasing, and the larger of decline oil production.
根据聚合物用量与聚合物驱经济效益的关系，确定聚合物驱合理用量。
Reasonable polymer injection amount is then determined according to the relationship between polymer injection amount and economic benefit of polymer flooding.
最后，综合对比三种方案的采出程度、压力和聚合物用量，确定高浓度试验区的最佳注入方案。
Last, through a comprehensive comparison of recovery Level, pressure and polymer dosage of three kinds of programs, best injection programs of test area of high concentration have been identified.
聚合物用量是聚合物驱开发过程中重要的设计参数，该参数设计的是否合理将直接影响到聚合物驱的总体效果。
Polymer volume is an important design parameter in the process of polymer flooding development, and its reasonable design can directly affect the overall effect of polymer flooding.
讨论了聚合物多元醇和水用量、低不饱和度聚醚等因素对泡沫性能的影响。
The effects of amounts of polymer polyol and water, low unsaturated polyether polyol on properties of foam were discussed.
控制项目主要包括进料量、反应温度、催化剂用量及配比、单体转化率、聚合物门尼粘度控制。
The controlled items mainly consist of feed quantity, reaction temperature, catalyst usage and ratio, conversion rate and polymer Mooney viscosity.
考察了聚合反应条件，如溶剂种类、聚合温度、模板浓度、引发剂用量、转速、预聚合时间等对分子印迹聚合物微球特性的影响。
The effects of reaction conditions were studied, including the kind of solvent, polymerization temperature, the concentration of template and initiator, rotational speed and pre-polymerization time.
讨论了分散介质、搅拌强度、磁性粒子性质及用量等因素对聚合反应及聚合物磁含量的影响。
The effects of the dispersing medium, the agitation intensity, the amount and properties of magnetic particles on the polymerization and magnetic content in the polymer microspheres are discussed.
结果表明，随着反应温度的升高或引发剂的用量增大，聚合物的特性粘度降低。
It was found that increasing the temperature and amount of initiator decreased the intrinsic viscosity of the copolymer.
用电子显微镜（SEM）考察了聚合物浓度、添加剂用量及种类对膜形态结构的影响。
The influence of polymer concentration, the type of additive and content of additive on the morphological structure has been surveyed by SEM.
添加剂是聚合物中起重要作用的组分，而且，每种添加剂都应尽可能在最佳用量下使用，以得到高品质的产品。
Additives are essential functional ingredients of polymers, and whenever possible, each should be used in optimum amounts for the attainment of high-quality products.
毛织物的整理效果与酶的活性、聚合物整理剂的性质、用量、前处理工艺和组分有关。
The finishing performance of woolen fabric was related to the activity of the enzyme and the properties, components and application of polymer finishing agents as well as the pretreatment processing.
再利用毯废料可以用于降低原料聚合物和木材纤维的用量，以较低的成本得到同等的产品。
The recycled carpet waste may be used to decrease the amount of both base polymer and wood filler to achieve an equivalent product at lower cost.
研究结果表明，聚合物涂膜的拉伸强度随UPA和EGDMA用量的增加均呈现先增大后减小的趋势；
The experimental results show that the tensile strength of emulsion films firstly increases and then decreases with the increase of the UPA and EGDMA dosages.
分析粒子形成过程中产生的水溶性聚合物的量和组成，可以看出DMAEMA用量增加水溶性聚合物增多。
A strong dependence of water soluble polymer (WSP) formation on DMAEMA concentration was found by analyzing the amount and content of water soluble polymer.
通过升高引发温度或增加不对称醚用量可以使苯乙烯在聚合物中呈现无规分布。
The styrene monomers of SIB were random by increasing reaction temperature or improving the dosage of asymmetrical ether BET.
结果表明，通过改变聚合物组分的配比和硫化剂的用量，可得到力学性能较好的复合材料。
Tensile testing shows that broad mechanical properties could be obtained by varying the component ratio of polymer and vulcanizing system.
利用适当用量的聚合物分散剂进行机械化学改性，可以得到良好分散的体系。
A well-dispersed system could be obtained by mechanochemical modification using appropriate dosage of polymer dispersants. In the white system, space...
重点介绍了使用共混聚合物作基体，并利用炭黑在共混基体中的非均相分布来降低炭黑用量的研究。
Emphasis is put on the studies using polymer blends as the matrix to lower the carbon black loading through the heterogeneous dist...
主要讨论了溶液酸度、萃取剂用量、盐用量、聚合物浓度、萃取时间等因素的影响。
This paper focuses on the functions of the elements such as the pH of solution, dosage of extraction solvent, dosage of salt, concentration of polymer, time of extraction.
评述了用金属系分散体作导电材料填充聚合物形成聚合物基ptc复合材料时所用金属系物质的种类、用量等对复合材料PTC强度的影响及其导电机理。
The effect of variety and quantity of the metals and their compounds on PTC intensity of composites and the electric conduction mechanism are discussed in detail.
我们建议的测试用量为聚合物有效固成分的1-3%。
It is recommended that the experimental dosage is 1-3% of active contents.
通过混凝土收缩试验，研究了水玻璃掺量、水玻璃模数、液固比、胶凝材料用量等因素对无机矿物聚合物混凝土收缩性能的影响。
The effect of various factors shrinkage property of slag based geopolymer concrete are studied by shrinkage test, such as content and modulus of water glass, liquid-solid ratio, gel material content.
结果表明，单体加入速度、聚合温度及引发剂用量是决定聚合物分子量的主要因素。
It has showed that the feeding speed of mixed monomers, temperature for polymerization and the dosage of initiator are main factors controlling the molecular weight.
探讨了引发剂类型与聚合温度的匹配，考察了分子量调节剂、溶剂用量、单位滴加时间等因素对聚合物分子量及其分布的影响。
Temperature, type of initiators, molecular regulator, addition time of monomers were investigated in terms of monomer conversion, molecular weight and its distribution.
探讨了单体丙交酯纯度、催化剂辛酸亚锡用量、反应时间、反应温度及真空度对聚合物相对分子质量的影响。
The effects of the synthesis conditions such as monomer(lactide) purity, catalyst(stannous octoate) concentration, vacuum level, reaction time and temperature, were discussed.
本文介绍了合成聚合物表面施胶剂AGP在胶版印刷纸和牛皮箱纸板生产中的应用试验，结果表明用AGP进行表面施胶能较大程度地提高纸的抗水性能，并可减少浆内施胶剂的用量。
The results proved that the use of the AGP as a surface sizing agent can improve the water-resistance of the paper and reduce the use of the internal sizing agent.
通过室内试验，考察了不同类型聚合物再利用剂的悬浮性，优化选择了YG340 - 1作为再利用剂，同时考察了聚合物再利用剂yg340 - 1的封堵性能、注入时机及用量。
The floatability of various flooding polymer reusing agents was evaluated in laboratory. YG340-1 was optimal reusing agent. Its plugging effect, inpouring time and inpouring amount were researched.
考察了聚合过程中水溶性引发剂用量、乳 化剂用量、引发剂种类、歧 化 松香含量等对单体转 化率和聚合物粒子粒径变 化的影响。
The influences of dosage of initiator, surfactant and DPR, and the type of initiator on polymerization were studied by monitoring the conversion of monomer and variation of particle size.
讨论了难燃接枝聚合物聚醚多元醇的用量对聚氨酯软质泡沫密度、氧指数和力学性能的影响。
The effects of FRGPPP content on density, oxygen index and mechanical properties of FPUF were investigated.
应用推荐